LevelOne FGP-2472 User Manual Download Page 164 | Manualshive

Page: 164 / 267

background image

158

3-23. Firmware Upgrade

Software upgrade tool is used to help upgrade the software function in order

to fix or improve the function. The switch provides a TFTP client for software
upgrade. This can be done through Ethernet.

Function name:

Firmware Upgrade

Function description:

The switch supports TFTP upgrade tool for upgrading software. If you assure
to upgrade software to a newer version one, you must follow two procedures:

1.) Specifying the IP address where TFTP server locates. In this field, the IP

address of your TFTP server should be filled in.

2.) Specifying what the filename and where the file is. You must specify full path

and filename.

Then, press <Upgrade> button if your download is not successful, the

switch will also be back to “Software Upgrade”, and it will not upgrade the
software as well.

When download is completed, the switch starts upgrading software. A

reboot message will be prompted after completing upgrading software. At this
time, you must reboot the switch to have new software worked.

Note: Software upgrade is hazardous if power is off. You must do it carefully.

Fig. 3-78

Parameter description:

TFTP Server: A TFTP server stored the image file you want to upgrade.

Path and Filename: File path and filename stored the image file you want to

upgrade.

«
...
162
163
164
165
166
...
»

Summary of Contents for FGP-2472












































































































































































































































































Reviews:

No comments

Related manuals for FGP-2472

xStack DGS-3420 Series

Brand: D-Link Pages: 2

Brand: D-Link Pages: 29

Brand: D-Link Pages: 454

Brand: D-Link Pages: 502

Brand: D-Link Pages: 244

Brand: D-Link Pages: 20

Brand: D-Link Pages: 2

Brand: D-Link Pages: 37

Brand: D-Link Pages: 28

Brand: B&K Pages: 2

Brand: B&B Electronics Pages: 45

Brand: Idem Pages: 2

LambdaUnite MSS

Brand: Lucent Technologies Pages: 388

SkyEdge II-c Capricorn Pro 4 AC Series

Brand: Gilat Pages: 2

Brand: FS Pages: 33

Brand: 3onedata Pages: 2

Brand: steute Pages: 20

Brand: SMC Networks Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands