Warning! Do not plug the power supply in until all wiring
is complete and leads are not exposed! Doing so will
could cause damage to the power unit and void the
warranty!
Remove precut insulation from sensor and power supply
wire ends. Connect wires as shown in Diagram 2 using wire
nuts provided. Bend wire nut connection flat to length of wire
and wrap with self-adhering tape making sure to create a
proper watertight seal. Apply a liquid electrical sealant
(available at most hardware stores) to each connection. We
recommend that the unit be tested before weatherproofing
the connectors.
Note: It does not matter which red wire from the valve or
black wire from the power unit are used when wiring.
Connection
Power Lead
Sensor Lead
Valve Lead
1
1 Black
1 Black
---
2
---
1st Red
1st Red
3
---
2nd Red
2nd Red
Plumbing the Unit
Using ¾” PVC pipe (available at most hardware stores) run
water supply from the fill valve outlet to the pond routing it
the way desired.
Parts needed:
•
Hacksaw (or other suitable fine-toothed saw)
•
PVC glue
•
Required lengths of 3/4” PVC
•
Required angle adapters.
Cut and fit all PVC pipe from the fill valve to the water
feature without gluing to make sure that the pipes are where
the user desires them.
Clean and glue all parts with general PVC cement to form a
watertight seal. Allow joints to dry for 24 hours before
connecting water to the system.
Plug the power supply into the weather-protected receptacle.
The unit is ready for operation
Operation
Once the
EasyFill X
TM
is connected properly and plugged in it
will fill anytime the water level drops below the sensor probe
window after an approximate 7 - 10 second delay.
Note! If the level of the water at the time of power up is low,
the unit will fill until the water level reaches the probes before
turning off.
Maintenance
The
EasyFill X
TM
requires very little maintenance. Periodically
clean the sensor probes thoroughly with the supplied wire
brush or equivalent to remove debris and film. No other
maintenance is required.
Troubleshooting
The MCX-11SW
EasyFill X
TM
Automatic Pond Leveling
Sensor should maintain the level in your pond for many
worry-free years. However, if you should experience
problems with it, it may be caused by some of these
common issues that can be resolved by the user:
Pond overflows when filling
Verify valve is installed upright, flow
direction is correct and manual fill screw
is tight.
Verify proper connections with the
sensor control.
Water may be at ground or voltage
potential. Measure with meter and
remove grounding source or check
submerged equipment for shorts.
Pond will not fill
Check to make sure power is available
at receptacle.
Check for debris on sensor probes and
clean per instructions.
Check to ensure connections are not
damaged and are covered with
weatherproof tape or sealant. Allow
connections to dry if necessary and seal
per the instructions.
Warranty
Aquility Systems, Inc warrants this product to the original
purchaser for a period of two years against defects in
material or workmanship when used for normal purposes it is
intended for. In order to obtain a replacement unit or repair
the existing unit, you must obtain a RMA number and return
the complete unit, postage prepaid, to the place of purchase,
or to the Aquility Systems facility. (6949 SW 21
st
Lane,
Gainesville, FL 32607)
This warranty is intended to cover product defects only.
Aquility Systems, Inc. is not liable for indirect, incidental or
consequential damages in connection with the use of the
Level Waters product covered by this warranty. This
warranty does not cover any cost or expense incurred by the
purchaser in providing substitute equipment or service
during reasonable periods of malfunction or non-use of this
product, while waiting for completion of repairs under this
warranty. Some states do not allow exclusions of incidental
or consequential damages, so the above exclusions may not
apply in all states. This warranty gives you specific legal
rights in your state, which vary from state to state.
If you wish to contact Aquility Systems, Inc., please direct
inquiries to:
Customer Service
Aquility Systems, Inc.
6949 SW 21
st
Ln.
Gainesville, FL 32607 or by email at
[email protected]
Copyright 2020 Aquility Systems, Inc. All Rights Reserved.
