manualshive.com logo in svg

Leuze electronic 50038948, Original Operating Instructions

Share
Download
Leuze electronic 50038948 Original Operating Instructions Download Page 34

Installation

32

BCL 8

Leuze electronic

6

Installation

6.1

Storage, transportation

Unpacking

Check the packaging content for any damage. If damage is found, notify the post office 

or shipping agent as well as the supplier.

Check the delivery contents using your order and the delivery papers:
• Delivered quantity
• Device type and model as indicated on the name plate
• Laser warning signs
• Brief manual

The name plates provide information as to what BCL type your device is. For specific infor

-

mation, please refer to Chapter 4.4.1.

BCL 8 name plate

Figure 6.1: BCL 8 device name plate

Save the original packaging for later storage or shipping.

If you have any questions concerning your shipment, please contact your supplier or your

local Leuze electronic sales office.

Observe the applicable local regulations when disposing of the packaging materials.

Cleaning

Clean the glass window of the BCL 8 with a soft cloth before mounting. Remove all pack

-

aging remains, e.g. carton fibers or Styrofoam balls.

 

ATTENTION!

Package the device for transport and storage in such a way that is protected against shock

and humidity. Optimum protection is achieved when using the original packaging. Ensure

compliance with the approved environmental conditions listed in the specifications.

BCL 8 type designation

 

ATTENTION!

Do not use aggressive cleaning agents such as thinner or acetone for cleaning the device.

UM_BCL8_de_50040581.book  Seite 32  Montag, 24. Februar 2020  9:53 09

Summary of Contents for 50038948











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands