manualshive.com logo in svg

Leuze electronic 1910i, Technical Description, Page: 19 / 27

Share
Download
Leuze electronic 1910i Technical Description Download Page 19

 

5.4  IT 1911i to PS2 interface 

The operation of the IT 1911i in keyboard-wedge mode is described in this chapter. A PC keyboard is 
emulated in this operating mode. The data which are read in are written directly to the currently activated 
program. Thus, the data can be processed further in all standard programs. 
 
Required parts: 
1x 

50122434 

IT 1911i ER-3 

1x 

50122431 

Base station IT 1911i 

1x   50114519 

KB PS2-1 IT190x 

1x 

50123862 

Power supply unit 

 
Please connect the base station acc. to the figure below.  
To do this, proceed as follows: 
1.  Switch off the PC. 
 
2.  Unplug the keyboard. 
 
3.  Connect the cable for the base station between 

the keyboard and the PC. 

 
4.  Switch the PC back on. 
 
5.  Scan the code shown below. 
 

NOTICE 

To charge the IT 1911i, the power supply unit must be plugged 

in and the hand-held scanner placed in the base station. 

5.4.1.1 

Configuration 

PS2 keyboard emulation with CR LF 
 
Return the IT 1911i to the base station so that the settings can be 
accepted. This procedure is concluded with an acoustic signal. 

 

Disconnect 

Leuze electronic 

IT1911i 

19 

Summary of Contents for 1910i




























Reviews:

No comments