background image

Page 1 of 8

TireBiter

  

Spare Tire Mount V-Rack™ Carrier for Two Bikes 

Part No. B00987

Revision Date: 10/21/19

TB-B00987-102119Rev

ASSEMBLY, INSTALLATION,  AND OPERATION INSTRUCTIONS

To register your product, visit the LetsGoAero.com/registration

For More Information & Accessories, Visit our Website - www.LetsGoAero.com

For Technical Support & Product Questions Contact Us at 877-464-2376 or 719- 630-3800

Email: [email protected] 

Let’s Go Aero, Inc. 4474 Barnes Road Colorado Springs, CO 80917, USA 

 

Patent and trademark protected. Patent Number 8,889,456; Patents Pending.

Maximum load weight limit is 35 lbs per bicycle.

For Rear Mounted Spare Tires.

NOTICE: 

All Manual information is subject to change without notice. Revised editions 

will be available for free download at LetsGoAero.com. Manual information is considered 

factual until made obsolete by a revised version. 

 

Follow this QR-Code or visit  

LetsGoAero.com/manuals to check for an updated version:

Copyright

© 

2019, Lets Go Aero, Inc., All rights reserved.

PRODUCT MANUAL

Watch the Assembly Video:

www.LetsGoAero.com/Videos

A

B

C

D

F

G

H

J

K

L

M

N

O

1

4

8

4

2

2

2

2

8

4

4

8

8

2

BASE

ANGLE BOLT

1/4” WASHER

1/4” NYLOCK NUT

RATCHET ASSEMBLY

LONG WEBBING STRAP

RATCHET COVERS

WING SUPPORT ARMS

CRADLE HOUSING

UPPER WHEEL CRADLE

LOWER WHEEL CRADLE

RUBBER STRAPS

SMALL RETAINER CLIPS

RING PIN

QTY.  DESCRIPTION

PARTS

Summary of Contents for TireBiter V-Rack









Reviews: