background image

– 7 –

G

ear

W

aGOn

™ 125

 

S

pOrT

 p

erfOrMance

 T

railer

GW 1125-9/12

Leveler Kit

The Leveler Kit is an integrated feature of the GearWagon 
125 Camping Trailer for stabilization of the trailer when 
removed from the vehicle’s hitch. 

Operation
•  To extend legs, pull leg outward to release the spring catch and detent 
    lance. Allow the leg to swing downward until the lance engages in the 
    extended slot position. 

•  To retract legs, first minimize the leg length to the shortest position, then 
    pull leg downward to release the lance from its extended and locked 
    position. Swing the leg upward into the retracted position until the lance 
    catches in the retracted slot. Before driving, verify that the legs are retracted 
    and that the locking lance is fully engaged in the locking slot.
 

 

Vertical 
and
horizontal
catch
positions

Height
adjustment
lever

WARNING:  Always fold up Leveler Kit in secure position before operating trailer. 
Do not move trailer with stabilizers down, or damage will occur.

To release from catch position, pull leveler forward (toward front of 
trailer).

Swing leveler down.

Adjust height by pressing downward on adjustment lever.

To prepare for transit, release adjustment lever to minimize leg 
length and fold upward to retracted, catched position shown 
above.

Summary of Contents for GearWagon 125 Camper


















Reviews: