manualshive.com logo in svg

Let's Go Aero Half Nelson, Product Manual

Share
Download
Let's Go Aero Half Nelson Product Manual Download Page 1

Page 1 of 10

Half Nelson 

2-Bike Truck Mount Carrier 

Part No. B01809

Revision Date: 07/15/19

HN-071519Rev

ASSEMBLY, INSTALLATION,  AND OPERATION INSTRUCTIONS

For More Information & Accessories, Visit our Website - www.LetsGoAero.com

For Technical Support & Product Questions Contact Us at 877-464-2376 or 719- 630-3800

Email: [email protected]

Copyright

© 

2019, Lets Go Aero, Inc., All rights reserved.

PATENT PROTECTED

PRODUCT MANUAL

Rated for 70 lbs (35 lbs per Bicycle) of payload. 

For Domestic Pickup trucks or Pickups without C-Channel Bed Attachments.

NOTICE: 

All Manual information is subject to change without notice. Revised editions 

will be available for free download at LetsGoAero.com. Manual information is considered 

factual until made obsolete by a revised version. 

 

Follow this QR-Code or visit  

LetsGoAero.com/manuals to check for an updated version:

Watch the 

Assembly Video:

LetsGoAero.com/Videos

Summary of Contents for Half Nelson











Reviews:

No comments

Brands by name

Popular brands

Load more brands