manualshive.com logo in svg

Let's Go Aero BLACK BOX, Product Manual

Share
Download
Let's Go Aero BLACK BOX Product Manual Download Page 20

PAGE 20 OF 21

OPERATION: Opening & Closing

Slide-out:

 Remove the Retainer Clip 

[

B

] 

and Hand-Tighten Pin 

[

D

] 

and set aside [Figure 59]. 

Standing on the side of the carrier that is furthest away from the vehicle, gripping from the underside of the 

carrier, pull the carrier horizontally away from the vehicle untill the Safety Cable is fully extended. 

Slide-in: 

Standing on the side of the carrier that is furthest away from the vehicle, gripping from metal tray, 

push the carrier back towards the vehicle until the holes for the Hand-Tighten Pin 

[

D

] 

re-align. 

Re-insert and fully thread the Hand-Tighten Pin 

[

D

]

. Secure with Retainer Clip 

[

B

]

. 

Do not push or pull on the carrier lid. Pushing or Pulling on the carrier lid during slide-out/in operation may cause 

warping of the lid over time. Failure to follow proper lid care may result in damage to carrier, damage to property, 

bodily injury or death.

Always ensure the Hand-Tighten Silent Hitch Pin is fully threaded and secured with retainer clip (or a Lets Go Aero 

Hitch Pin Lock) before transit. Failure to the Hand-Tighten Pin may result in damage to carrier, damage to property, 

bodily injury or death.

      WARNING:

 

      WARNING:

 

D

B

[Figure 59]

Summary of Contents for BLACK BOX






















Reviews:

No comments

Brands by name

Popular brands

Load more brands