background image

 

 
Summit Series ® 

4 of 20 

User’s Manual 

 

IMPORTANT SAFETY INSTRUCTIONS 

 

1. 

SAVE THESE INSTRUCTIONS 

– This manual contains important safety and operating instructions. 

 
2. 

Before  using  battery  charger,  read  all  instructions  and  cautionary  markings  on  battery  charger, 
battery, and product using battery. 

 
 

             

 

LOOK  FOR  THIS  SYMBOL  TO  POINT  OUT  SAFETY  PRECAUTIONS. 
IT  MEANS: 

BE  ALERT

—YOUR  SAFETY  IS  INVOLVED.   

IF  YOU  DO 

NOT  FOLLOW  THESE  SAFETY  INSTRUCTIONS,  INJURY  OR 
PROPERTY DAMAGE CAN OCCUR. 

 
 

3. 

DANGER:    TO  REDUCE  THE  RISK  OF  FIRE  OR  ELECTRIC  SHOCK,  CAREFULLY  READ  AND 

FOLLOW  THESE  IMPORTANT  SAFETY  AND  OPERATING  INSTRUCTIONS  BEFORE  INSTALLING 
OR OPERATING THE CHARGER. 

 

4. 

INSTRUCTIONS IMPORTANTES CONCERNANT LA SECURITÉ. 

 

5. 

WARNING:    TO  REDUCE  THE  RISK  OF  FIRE,  INSTALL  THIS  BATTERY  CHARGER  ON  A 

SURFACE OF NON-COMBUSTIBLE MATERIAL SUCH AS BRICK, CONCRETE, OR METAL. 

 

6. 

DANGER:    RISK  OF  ELECTRIC  SHOCK.    DISCONNECT  CHARGER  FROM  BATTERY  AND  AC 

POWER BEFORE SERVICING.  TURNING OFF THE CHARGER DOES NOT REDUCE THIS RISK. 

 

7. 

DANGER:  RISK OF ELECTRIC SHOCK.  DO NOT TOUCH UNINSULATED PORTION OF AC OR 

DC CONNECTORS OR UNINSULATED BATTERY TERMINAL. 

 

8. 

DANGER:    RISQUE  DE  CHOCKS  ÉLECTRIQUES.    NE  PAS  TOUCHER  LES  PARTIES  NON 

ISOLÉES DU CONNECTEUR DE SORTI OU LES BORNES NON ISOLÉES DE L’ACCUMULATEUR. 

 

9. 

CAUTION:  CHARGE ONLY BATTERIES OF THE SAME TYPE, VOLTAGE, CELL NUMBER, AND 

AMP-HOUR  CAPACITIES  AS  SHOWN  ON  THE  LABEL.    OTHER  TYPES  OF  BATTERIES  MAY 
BURST CAUSING PERSONAL INJURY AND DAMAGE.  BEFORE CHARGING ANY OTHER TYPE OF 
RECHARGEABLE  BATTERY,  CHANGE  THE  CHARGER  SETTINGS  AS  RECOMMENDED  BY  THAT 
BATTERY MANUFACTURER. 

 

10. 

ATTENTION:  UTILISER POUR CHARGER UNIQUEMENT LES ACCUMULATEURS AU PLOMB À 

ELECTROLYTE  LIQUIDE.    D’AUTRES  TYPES  D’ACCUMULATEURS  POURRAIENT  ÉCLATER  ET 
CAUSER DES. 

 

11. 

DANGER:    TO  PREVENT  ELECTRICAL  SHOCK,  DO  NOT  TOUCH  EITHER  AC  OR  DC 

UNINSULATED PARTS.  MAKE SURE ALL ELECTRICAL CONNECTORS ARE IN GOOD WORKING 
CONDITION.  DO NOT USE CONNECTORS THAT ARE CRACKED, CORRODED OR DO NOT MAKE 
ADEQUATE  ELECTRICAL  CONTACT.    USE  OF  A  DAMAGED  OR  DEFECTIVE  CONNECTOR  MAY 
RESULT IN A RISK OF OVERHEATING OR ELECTRIC SHOCK. 

 

12. 

WARNING:  HAZARD OF ELECTRIC SHOCK. 

 

13. 

WARNING:    LEAD-ACID  BATTERIES  GENERATE  EXPLOSIVE  GASES.    TO  PREVENT  ARCING 

OR BURNING NEAR BATTERIES, DO NOT DISCONNECT DC CHARGING CORD FROM BATTERIES 

Summary of Contents for SUMMIT 27940





















Reviews: