background image

LST-GM1 Switching Steps

LST-GM1

EN

LESITE

4、Turn on the motor switch (26), and turn the speed knobs (24) (25) to set the required 

welding speed

(the LCD screen displays as shown in Drawing 3.), then insert the membrane layers after 

placing the machine

5、Put down the pressure handle(1) ,the machine starts to move and weld

6、Keep observing the welding trail and the position of the upper layer and lower layer at 

any time to adjust in case of deviation

7、After finishing welding, lift up the pressure handle (1),move the machine away from the 

welding position

8、Turn off the motor switch(26),press the temperature rise knob (22)and the 

temperature drop knob at the same time(23)(As shown in drawing 4),or turn the 

temprature drop knob to “OFF”,the hot wedge will stop heating

9、Turn off the power switch

Current Temperature

Current Temperature

Preset Temperature

Current Speed

Drawing 1

Drawing 2

Drawing 3

Drawing 4

Preset Speed

Current Speed

Preset Speed

Current Temperature

Preset Temperature

Current Speed

Preset Speed

Current Temperature

Current Speed

Preset Speed

1、Connect the power supply, lift up the pressure handle (1) and the pressure roller (5)

to separate automatically

2、Turn on the power switch (21), the LCD screen displays as shown in drawing 1 While

the hot wedge has not started to heat up

3、Turn the temperature rise knob (22) so the LCD screen displays as shown in drawing 2 

While the hot wedge starts to heat until the actual temperature is equal to the preset 

temperature

Summary of Contents for LST-GM1













Reviews: