background image

1. Welding temperature:

Press the buttons                    on the panel to set the required welding temperature , 

which depends on the weldiing material and ambient temperature. The LCD screen will

display the preset temperature and the current actual temperature.

2. Welding speed:

Press the buttons                   on the panel to set the required welding speed,which

matchs the welding temperature.The LCD screen will display the preset speed and the

current actual speed.

3.Motor is on:

Press            the motor moves

● This machine has a parameter storage memory function that the welding machine will

automatically use the last parameters without resetting the parameters when the machine
is turned on next time.

LST-GM1 Control Panel

LST-GM1

EN

LESITE

21

22

23

24

25

26

20

19

18

17

17、Motor Fuse                                           18、Welding Speed Display     

19、Welding Temperature Display        20、Power Fuse

21、Power Switch                                      22、Temperature Rise Knob

23、Temperature Drop Knob                  24、Speed Increase Knob

25、Speed Down Knob                            26、Motor Switch                                

Summary of Contents for LST-GM1













Reviews: