background image

Shenzhen LEPU Intelligent Medical Equipment Co., Ltd.

Form No.: LP-QR-RD-016 REV.01

Page 6of 7

The ambient temperature is

lower than 5°C

Move to another warm room

The ambient temperature is

higher than 40°C

Move to another cold room

1.19 Other error messages

Error message on screen

Meaning of show

Possible causes and solutions

Eeprom error

Please contact the after-sales service.

Hardware error

Please contact the after-sales service.

Cleaning and Maintenance

Clean with a dry soft cloth. If the engine is particularly dirty, wipe with a wet and wrung out

cloth and then dry it with a dry cloth. Disinfect the product only when necessary; disinfection is

recommended to carry out by wiping the product surface twice with disinfectant. Do not soak or

use gas for disinfection. Use of medical alcohol is recommended.

If necessary, clean the infrared forehead thermometer first when repeated measurement of the

body temperature is required. Clean the thermometer shell and sensor with alcohol swab or cotton

ball dipped in alcohol (70%), and be careful to avoid liquid entering the thermometer. No use of

corrosive detergent, diluent or benzene solvent is allowed. Do not immerse the thermometer in

water or other cleaning solutions of any kind.

Do not expose the equipment to high temperature, high humidity, dust or direct sunlight.

Remove the battery when the thermometer will not be used for a long time.

Summary of Contents for LFR30B








Reviews: