background image

 

 

FCC Notice 

This  equipment  has  been  tested  and  found  to  comply  with  the  limits  for  a  Class-A  digital  device, 

pursuant  to  Part  15  of  the  FCC  rules.  These  limits  are  designed  to  provide  reasonable  protection 

against  harmful  interference  in  a  residential  installation.  This  equipment  generates,  uses,  and  can 

radiate  radio  frequency energy.  It  may cause  harmful  interference  to radio  communications  if the 

equipment  is  not  installed  and  used  in  accordance  with  the  instructions.  However,  there  is  no 

guarantee that interference will not occur in a particular installation. If this equipment does cause 

harmful  interference  to  radio  or  television  reception,  which  can  be  determined  by  turning  the 

equipment off and on, the user is encouraged to try to correct the interference by one or more of 

the following measures: 

• 

Reorient or relocate the receiving antenna. 

• 

Increase the separation between the equipment and receiver. 

• 

Connect  the  equipment  into  an  outlet  on  a  circuit  different  from  that  to  which  the 

receiver is connected. 

• 

Consult the dealer or an experienced radio/TV technician for help. 

 

Caution: Any changes or modifications not expressly approved by the grantee of this device could 

void the user's authority to operate the equipment. 

 

CE Mark Warning 

This  is  a  Class-A product.  In  a  domestic  environment this  product  may  cause  radio  interference  in 

which case the user may be required to take adequate measures. 

 

This document is the current official release manual. Please check our website (www.leonton.com) 

for any updated manual or contact us by e-mail ([email protected]). 

 

 

Summary of Contents for GINJ-0201-AT-24 Series


















Reviews: