background image

OPTIONAL OUTLET SETUP PIPING

(BY OTHERS)

The addition of this piping arrangement (extra 
tee and ball valve) eliminates the need to turn 
fixtures on and off throughout the building at 
setup. The flows required in the setup 
instructions (page 3) are set by using Ball Valve 
A. (make sure main outlet ball valve is closed).

MAIN OUTLET

 BALL VALVE

BALL VALVE A

10

-10

20

0

40

14

0

°F

0

60

°C

50

LEONARD

20

40

R

30

12

0

10

0

60

80

TEMPERED WATER

TO BUILDING

CAUTION! ALL THERMOSTATIC WATER MIXING VALVES AND SYSTEMS HAVE 
LIMITATIONS! THEY WILL NOT PROVIDE THE DESIRED PERFORMANCE OUTSIDE 
OF THEIR FLOW CAPACITY RANGE! CONSULT THE CAPACITY CHART BELOW 
AND OBSERVE MINIMUM FLOWS SHOWN.

FLOW CAPACITIES

MINIMUM

(l/min)

(GPM)

FLOW

2.0

8

541

454

273

371

10

98

.7

.3

72

5

1.4

.97

120 143

15

20

795

681

738

636

2.1

1.7

168

180

25

30

2.8

2.4

195

210

35

40

SYSTEM PRESSURE DROP (PSIG)

897

939

l/min

3.1

3.4

237

248

45

50

GPM

PSI

BAR

TM-1520A-DT

PARALLEL

SYSTEM PRESSURE DROP (PSIG)

MINIMUM

(l/min)

(GPM)

FLOW

2.0

8

825

734

442

640

10

169

.7

117

.3

5

194 218

15

.97

1.4

20

1120

977

1067

927

245

258

1.7

25

2.1

30

282

296

2.4

35

40

2.8

l/min

1215 1283

321

339

3.1

45

3.4

50

GPM

PSI

BAR

TM-2020A-DT

PARALLEL

LIMITED WARRANTY

Leonard Valve Company warrants the original purchaser that products manufactured by them (not by others) will 
be free from defects in materials and workmanship under normal conditions of use, when properly installed and 
maintained in accordance with Leonard Valve Company's instructions, for a period of one year from date of 
shipment. During this period the Leonard Valve Company will at its option repair or replace any product, or part 
thereof, which shall be returned, freight prepaid, to the Leonard factory and determined by Leonard to be 
defective in materials or workmanship. There are no warranties, express or implied, which extend beyond the 
description contained herein. There are no implied warranties of merchantability or of fitness for a particular 
purpose. In no event will Leonard be liable for labor or incidental or consequential damages. Any alteration or 
improper installation or use of the product will void this limited warranty.

12

Printed in USA

Summary of Contents for TM-1520A-DT













Reviews: