(13360122)
Lenze Americas • 630 Douglas Street • Uxbridge, MA 01569 • USA
Sales: (800) 217-9100 • Service: (508) 278-9100 • www.lenzeamericas.com
KM01C
13360122
Reverse/Forward key: Selects Forward or Reverse direction.
The
R/F key is only active if Parameter 17 - ROTATION is
set to “02” (FORWARD AND REVERSE).
When the
R/F key is pressed, the symbol for the opposite
direction will blink on the display. Press the
M key within
four seconds to confirm the rotation change.
Below are the display symbols used to indicate direction:
FORWARD
REVERSE
6.
REMOTE KEYPAD FUNCTIONS
The
M key and the
p
and
q
keys on the remote keypad function the
same as the
Mode button and the
p
and
q
buttons on the drive. The
other remote keypad functions are described below:
STOP key: Press STOP to Stop the drive. The STOP key
is active whenever the remote keypad is operational.
RUN key: Press RUN to Start the drive. TB-1 must be closed
to TB-11. See the wiring diagram in Section 4.
5.
SETTING UP THE SCL/SCM DRIVE
To set up the SCL/SCM drive to work with the Remote Keypad, the
following parameters must be programmed:
P11 TB-13B FUNCTION
Set to REMOTE KEYPAD (13)
P12 TB-13E FUNCTION
Set to REMOTE KEYPAD (21)
P14 CONTROL
Set to REMOTE KEYPAD ONLY (02).
When this is done, and the Remote Keypad is connected, only the Remote
Keypad can start the drive and select direction. This results in some
functions of the drive being unavailable. These are explained below:
1.
The Dynamic Braking option cannot be used because TB-13E is
required for the Remote Keypad.
2.
Settings 05, 06, and 07 on TB-13A (Parameter 10) are disabled.
These settings are related to direction control. Only the Remote
Keypad can be used for direction commands.
Refer to the SCL/SCM Installation and Operation Manual for more
information.
Note:
Once the drive is set up for Remote Keypad control, the buttons on
the front of the drive are disabled. If they are pressed, the drive display
and Remote Keypad display will show “SE”, indicating that the buttons
are disabled.
8.
TROUBLESHOOTING
CONDITION / DISPLAY
POSSIBLE CAUSES
Remote Keypad display
is blank, or only the
decimal points are
illuminated.
Parameter 14 - CONTROL is set to “01”
(TERMINAL STRIP ONLY).
Parameter 11 - TB-13B is not set to “13”.
Parameter 12 - TB-13E is not set to “21”.
The Remote Keypad is not wired correctly
to the drive.
Remote Keypad and/or
SCL/SCM drive displays
“JF”.
“JF” typically indicates a communication
problem. Check for proper wiring between
the remote keypad and the drive.
A “JF” fault can also occur if an attempt
is made to start the drive and TB-1 is not
closed to TB-11.
The
R/F key does not
work to change rotation
direction.
To use the
R/F key to change rotation
direction, Parameter 17 - ROTATION
must be set to “02” (FORWARD AND
REVERSE).
Once the desired rotation direction is
selected, the
M key must be pressed within
4 seconds to confirm the change.
R F
RUN
STOP
WARNING!
If the remote keypad display is totally blank or only the decimal points
are lit, or is displaying a “JF” fault, the
STOP key WILL NOT stop the
drive. The remote keypad must be operational in order for the
STOP
key to be active
7.
REMOTE KEYPAD DISPLAY
The SCL/SCM Remote Keypad has a three digit display like the
SCL/SCM drive.
The displays below are examples of the drive in RUN mode. On the
left, the drive is running at 43.6 Hz. On the right, the speed has been
changed to 52.8 Hz (during speed command changes, the upper left
decimal point turns on).
The displays below are examples of problems that will occur if the drive
is not properly programmed or if the keypad is not wired properly to the
drive.
Make sure Parameters
11, 12, and 14 are
properly set.
Make sure the keypad
is properly wired to the
drive and the cable is
away from noise.
