manualshive.com logo in svg

Lenze E84DGFCp Series, Communications Manual

Share
Download
Lenze E84DGFCp Series Communications Manual Download Page 29

EDS84DMOTPBUS EN 3.0 - 11/2011

L

29

Communication manual 8400 motec PROFIBUS

Commissioning

Configuring the host (master)

   

6.2

Configuring the host (master)

For communication with the controller, you have to configure the host (master) first.

Configuration for the host (master) and the DP-V0 parameter data channel

For the configuration of the PROFIBUS, the PROFIBUS device description file of the Inverter

Drive 8400 motec must be read into the master.
The device description file is available on Lenze's website in the "Services & Downloads"

area at:

www.Lenze.com

 

The following language variants of the device description file can be used:

LENZE84D.GSD (source file, English)

LENZE84D.GSG (German)

LENZE84D.GSE (English)

Defining the user data length

The user data length is defined during the initialisation phase of the master.
The communication unit PROFIBUS supports the configuration of max. 8 process data

words (max. 16 bytes).
The user data lengths for process input data and process output data are the same.

Summary of Contents for E84DGFCp Series





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands