Lenze AC Tech ESVZAP0 Communications Interface Reference Manual Download Page 44

Page: 44 / 49

CMVPFB01A

Advanced Features

7.6.2 Sync and Freeze Status

P421 - Sync and Freeze Status

Default: N/A

Range: 0 - 7

Access: RO

Type: Bit

Table 38: Sync and Freeze Status

P421 Value

Description

Bit 0

Reserved

Bit 1

Clear Out Data

Bit 2

Unfreeze

Bit 3

Freeze

Bit 4

Unsync

Bit 5

Sync

Bit 6

Reserved

Bit 7

Reserved

7.7 Data Sizes

7.7.1 Dout Data Size

P449 - Dout Data Size (in Bytes)

Default: N/A

Range: 0 - 20

Access: RO

Type: Integer

This parameter displays in bytes the total amount of Dout data including outward going 4WPA data.

7.7.2 Din Data Size

P469 - Din Data Size (in Bytes)

Default: N/A

Range: 0 - 20

Access: RO

Type: Integer

This parameter displays in bytes the total amount of Din data including incoming 4WPA data.

7.8 Debug Data Viewer

The Debug Data Viewer parameters enable the viewing of raw data being passed between the network
master and the option module.

7.8.1 Dout Data Monitor Select

P450 - Dout Data Monitor Select

Default: 0

Range: 0 - 255

Access: R/W

Type: Integer

This parameter selects which Dout word (including 4WPA) of data will be monitored.

Summary of Contents for ESVZAP0


















































Search results

Summary of Contents for ESVZAP0

Reviews:

Related manuals for ESVZAP0

Brands by name

Popular brands

Lenze AC Tech ESVZAP0, Communications Interface Reference Manual

Search results

Summary of Contents for ESVZAP0

Reviews:

Related manuals for ESVZAP0

Brands by name

Popular brands