Lenovo V145 Hardware Maintenance Manual Download Page 43

Page: 43 / 75

Lenovo V145

1060 PCI Express Mini Card for wireless LAN

For access, remove these FRUs in order:
•  “1010 Optical drive” on page 32
•  “1020 Base cover” on page 33
•  “1030 Battery pack” on page 35

Important:

The preinstalled WLAN module may only be replaced with a

Lenovo approved module in order to comply with FCC and IC regulations.

Refer to “Table 4. Parts list-Overall (Lenovo V145-14AST)” on page 59 or

“Table 9. Parts list-Overall (Lenovo V145-15AST)” on page 65 for Lenovo

part numbers for the approved modules.

Figure 6. Removal steps of PCI Express Mini Card for wireless LAN

Peel off the tape

Disconnect the two wireless LAN cables (black, gray) . Remove the screw .

In step , unplug the antenna RF connector (P/N: 08K7159) by using the
removal tool, or pick up the connectors with your fingers and gently unplug

them in the direction shown by the arrows.

Notes:

The wireless LAN card has 2 cables in step .

The wireless LAN card in some models might have 3 cables in step .

Step Screw (quantity)

Color

Torque

M2 × 3.5 mm, Phillips head, nylok-coated (1)
WLAN CARD TO UPPER

Silver

1.85±0.15 kgf*cm

Summary of Contents for V145












































































Search results

Summary of Contents for V145

Reviews:

Related manuals for V145

Brands by name

Popular brands

Lenovo V145, Hardware Maintenance Manual

Search results

Summary of Contents for V145

Reviews:

Related manuals for V145

Brands by name

Popular brands