Lenovo thinksystem SN850 7X15 Setup Manual Download Page 66

Page: 66 / 88

node. Retention clips that secure the I/O expansion adapters must be in the closed position to
install the compute node cover.

Step 3. Hold the front of the compute node and slide the compute node cover forward to the closed

position, until it clicks into place.

1. Install the compute node into the chassis (see “Install a compute node ” on page 58 for instructions).

Install a compute node

Use this information to install a compute node.

To avoid possible danger, read and follow the following safety information.

S021

CAUTION:
Hazardous energy is present when the compute node is connected to the power source. Always
reinstall the compute node cover before installing the compute node.

Before you install a compute node:

Read “Installation Guidelines” on page 26 to ensure that you work safely.

To install a compute node, complete the following steps:

Watch the procedure

. A video of the installation process is available:

• Youtube: https://www.youtube.com/playlist?list=PLYV5R7hVcs-DtV8A4UWy7d3AoFKjCvas3
• Youku: http://list.youku.com/albumlist/show/id_50481024

Figure 41. Compute node installation

ThinkSystem SN850 Compute Node Setup Guide

Summary of Contents for thinksystem SN850 7X15

























































































Search results

Summary of Contents for thinksystem SN850 7X15

Reviews:

Related manuals for thinksystem SN850 7X15

Brands by name

Popular brands

Lenovo thinksystem SN850 7X15, Setup Manual

Search results

Summary of Contents for thinksystem SN850 7X15

Reviews:

Related manuals for thinksystem SN850 7X15

Brands by name

Popular brands