Lenovo ThinkStation P360 Tower Hardware Maintenance Manual Download Page 93 | Manualshive

Page: 93 / 116

Lenovo ThinkStation P360 Tower Hardware Maintenance Manual Download Page 93

2. Position the new heat-sink-and-fan assembly on the system board. Ensure that the four screws are

aligned with the holes in the system board. Follow the following sequence to tighten the four screws to
secure the new heat-sink-and-fan assembly to the system board. Do not over-tighten the screws. Then,
install the four screws to secure the new heat-sink-and-fan assembly to the chassis.

• Partially tighten screw

2a

, fully tighten screw

2b

, and then fully tighten screw

2a

.

• Partially tighten screw

2c

, fully tighten screw

2d

, and then fully tighten screw

2c

.

Notes:

• Apply appropriate amount of thermal grease to the new heat-sink-and-fan assembly.

• In case you need to install the chassis beam as well, ensure that it has been installed in place before

you install the 125-watt heat-sink-and-fan assembly.

Hardware removal and installation

87

«
...
91
92
93
94
95
...
»

Summary of Contents for ThinkStation P360 Tower





















































































































Reviews:

No comments