manualshive.com logo in svg

Lenovo ThinkStation P360 Tower, Hardware Maintenance Manual, Page: 67 / 116

Share
Download
Lenovo ThinkStation P360 Tower Hardware Maintenance Manual Download Page 67

3.5-inch primary hard disk drive cage

Prerequisite

Before you start, read 

Generic Safety and Compliance Notices

, and print the following instructions.

Attention:

The internal storage drive is sensitive. Inappropriate handling might cause damage and 

permanent loss of data. When handling the internal storage drive, observe the following guidelines: 

•  Replace the internal storage drive only for upgrade or repair. The internal storage drive is not designed for 

frequent changes or replacement.

•  Before replacing the internal storage drive, make a backup copy of all the data that you want to keep.

•  Do not touch the contact edge of the internal storage drive. Otherwise, the internal storage drive might get 

damaged.

•  Do not apply pressure to the internal storage drive.

•  Do not make the internal storage drive subject to physical shocks or vibration. Put the internal storage 

drive on a soft material, such as cloth, to absorb physical shocks.

Chapter 7

.

Hardware removal and installation

61

Summary of Contents for ThinkStation P360 Tower





















































































































Reviews:

No comments