manualshive.com logo in svg

Lenovo ThinkStation P350 Tiny, User Manual, Page: 86 / 100

Share
Download
Lenovo ThinkStation P350 Tiny User Manual Download Page 86

Removal steps

Note:

After installing a new coin-cell battery, reset the system date and time in the UEFI BIOS menu.

Power supply assembly

Prerequisite

Before you start, read 

Generic Safety and Compliance Notices

, and print the following instructions.

Although there are no moving parts in the computer after the power cord has been disconnected, the 
following warnings are required for your safety.

Keep fingers and other parts of your body away from hazardous, moving parts. If you suffer an injury, seek 
medical care immediately. Never remove the cover on a power supply or any part that has the following label 
attached.

Hazardous voltage, current, and energy levels are present inside any component that has this label attached. 
There are no serviceable parts inside these components. If you suspect a problem with one of these parts, 
contact a service technician.

For access, do the following: 

1.  Remove these parts in order, if any: 

•  “Computer cover” on page 42

•  “Optical drive” on page 43

•  “Front bezel” on page 45

•  “Primary storage drives” on page 46

•  “3.5-inch primary storage drive cage” on page 51

2.  Disconnect the power supply assembly cables from the system board.

80

P350 User Guide

Summary of Contents for ThinkStation P350 Tiny





































































































Reviews:

No comments