Lenovo ThinkAgile VX 4-Socket 4U Certified Node User Manual Download Page 52 | Manualshive

Page: 52 / 296

background image

• Cable identifiers of some cables are printed on the cables that come with the server and optional devices.

Use these identifiers to connect the cables to the correct connectors.

• Ensure that the cable is not pinched and does not cover any connectors or obstruct any components on

the system board.

• Ensure that the relevant cables pass through the cable clips.

Note:

Disengage all latches, release tabs, or locks on cable connectors when you disconnect cables from

the system board. Failing to release them before removing the cables will damage the cable sockets on the
system board, which are fragile. Any damage to the cable sockets might require replacing the system board.

Cable routing for common components

Use this section to understand how to route cables for common server components.

Cable routing for common components is different for the lower and upper trays:

• “Common cable routing (lower tray)” on page 42
• “Common cable routing (upper tray)” on page 44

Notes:

• Make sure that all the cables go through the cable guides, as shown in the illustrations. See “Cable

guides” on page 41 for cable guide locations and descriptions.

• Some cable connectors have locks or latches that must be disengaged to disconnect the cable.

Common cable routing (lower tray)

The following illustration shows cable routing for common components in the lower tray.

42

User Guide for ThinkAgile VX7820 Appliance, ThinkAgile VX 4-Socket 4U Certified Node

«
...
50
51
52
53
54
...
»

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Reviews:

No comments

Related manuals for ThinkAgile VX 4-Socket 4U Certified Node

Brand: NEC Pages: 74

Express5800/T120e

Brand: NEC Pages: 6

Express5800/T120e

Brand: NEC Pages: 2

Express5800/T110i

Brand: NEC Pages: 2

EXPRESS5800/R320d-E4

Brand: NEC Pages: 19

Express5800/R320d-M4 Series

Brand: NEC Pages: 98

Express5800/R120h-2M

Brand: NEC Pages: 2

Express5800/R120f-1E

Brand: NEC Pages: 12

Express5800/R120d-1E

Brand: NEC Pages: 2

Express5800/R110i-1

Brand: NEC Pages: 2

Express5800/R110h-1

Brand: NEC Pages: 40

Express5800/A2040d

Brand: NEC Pages: 83

Express5800/320Lc

Brand: NEC Pages: 4

Express5800/120Rj-2

Brand: NEC Pages: 2

Brand: NEC Pages: 106

Express5800/T120d

Brand: NEC Pages: 153

Express5800/T110g-S

Brand: NEC Pages: 128

Express5800/R120g-1E

Brand: NEC Pages: 224

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands