Lenovo ThinkAgile VX 4-Socket 4U Certified Node User Manual Download Page 51 | Manualshive

Page: 51 / 296

background image

Note:

Disengage all latches, release tabs, or locks on cable connectors when you disconnect cables. Failing

to release them before removing the cables will damage the cable connectors or the cable sockets on circuit
boards, which are fragile. Any damage to the cable connectors or cable sockets might require replacing the
cables or circuit boards.

Some options, such as RAID controllers, might require additional internal cabling. See the documentation
that is provided for the option to determine any additional cabling requirements and instructions.

Cable guides

Make sure that all the cables go through the cable guides, as shown in each cabling section.

Figure 29. Cable guide locations

Connecting cables

To connect cables, observe the following guidelines:

• Disconnect all power cords from the server before you connect or disconnect any internal cables.
• See the documentation that comes with any external devices for additional cabling instructions. It might

be easier for you to route cables before you connect the devices to the server.

.

Server components

41

«
...
49
50
51
52
53
...
»

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Reviews:

No comments

Related manuals for ThinkAgile VX 4-Socket 4U Certified Node

Univerge SV9100

Brand: NEC Pages: 78

UNIVERGE SL2100

Brand: NEC Pages: 34

Brand: NEC Pages: 2

Brand: NEC Pages: 975

SUPERSERVER 5018D-MHR7N4P

Brand: Supermicro Pages: 126

ProLiant DL180 Gen10

Brand: HPE Pages: 10

Brand: Supero Pages: 112

FusionServer 5288 V6

Brand: xFusion Digital Technologies Pages: 131

UniServer R4900 G3

Brand: H3C Pages: 24

Brand: Conceptronic Pages: 127

Brand: HIKVISION Pages: 13

Brand: SmartSight Pages: 113

Brand: Hamlet Pages: 76

Brand: Docomo Pages: 61

SuperServer 2029BT-HNC0R

Brand: Supermicro Pages: 148

Brand: TRENDnet Pages: 9

Picturall MST02-R1

Brand: Analog way Pages: 4

NetNumen U31 R06

Brand: Zte Pages: 128

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands