Lenovo ThinkAgile VX 4-Socket 4U Certified Node User Manual Download Page 235 | Manualshive

Page: 235 / 296

background image

Figure 133. Storage board assembly removal

Step 1. Disconnect all cables on the storage board assembly that go to connectors in the storage tray. See

“Internal cable routing” on page 40.

Step 2. Press the release clips on the lower board of the storage board assembly and slide the storage

board assembly out of the storage tray.

After you remove the storage board assembly, install the storage tray and front cover. See “Install the
storage tray (fully removed)” on page 234 and “Install the front cover” on page 132.

If you are instructed to return the storage board assembly, follow all packaging instructions, and use any
packaging materials for shipping that are supplied to you.

Install a storage board assembly

Install a storage board assembly by inserting it in the storage tray, pushing it in until it locks in place, and

connecting the cables.

S002

CAUTION:
The power-control button on the device and the power switch on the power supply do not turn off the
electrical current supplied to the device. The device also might have more than one power cord. To
remove all electrical current from the device, ensure that all power cords are disconnected from the
power source.

” on page 89 “

Complete the following steps to install the storage board assembly:

.

Hardware replacement procedures

225

«
...
233
234
235
236
237
...
»

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Reviews:

No comments

Related manuals for ThinkAgile VX 4-Socket 4U Certified Node

Brand: Mako Pages: 56

Brand: NComputing Pages: 95

Brand: Avaya Pages: 84

SUPERSERVER 5015M-NT

Brand: Supero Pages: 134

Brand: Ekselans Pages: 37

eServer xSeries 335 Type 8676

Brand: IBM Pages: 178

PRIMERGY CX400 M6

Brand: Fujitsu Pages: 209

PRIMERGY CX272 S1

Brand: Fujitsu Pages: 234

Primergy CX270 S2

Brand: Fujitsu Pages: 320

Primergy CX270 S2

Brand: Fujitsu Pages: 56

Cortex-M7 Series

Brand: USR IOT Pages: 50

Usb Peripheral Server/5

Brand: Black Box Pages: 10

Brand: Black Box Pages: 3

Brand: Tibbo Pages: 21

LANTIME IMS-M500

Brand: Meinberg Pages: 63

Brand: LG-Ericsson Pages: 54

Brand: EEG Pages: 32

Image Server 2000 V-2000

Brand: 360 Systems Pages: 137

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands