Lenovo ThinkAgile VX 4-Socket 4U Certified Node User Manual Download Page 219 | Manualshive

Page: 219 / 296

background image

Before you remove a lower RAID flash power module:

1. Remove the front cover. See “Remove the front cover” on page 131.
2. Remove the lower compute tray or extract it to the maintenance position. See “Remove a compute tray”

3. Remove the lower fan cage. See “Remove a fan cage (lower tray)” on page 123.
4. Locate the RAID flash power module in the compute tray.

Complete the following steps to remove a lower RAID flash power module.

Watch the procedure

. A video of the installation process is available:

•

•

Figure 122. Lower RAID flash power module removal

Step 1.  Press the release tab and rotate the RAID flash power module upward.
Step 2.  Disconnect the cable from the RAID flash power module.
Step 3.  Remove the RAID flash power module from the compute tray.

If you are instructed to return the RAID flash power module, follow all packaging instructions, and use any
packaging materials for shipping that are supplied to you.

Install a RAID flash power module (upper tray)

The upper RAID flash power module is in the upper compute tray or optional storage tray that is accessed

from the front of the server. Insert the RAID flash power module in its carrier; then, connect the cable.

S002

CAUTION:
The power-control button on the device and the power switch on the power supply do not turn off the
electrical current supplied to the device. The device also might have more than one power cord. To

.

Hardware replacement procedures

209

«
...
217
218
219
220
221
...
»

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Reviews:

No comments

Related manuals for ThinkAgile VX 4-Socket 4U Certified Node

BladeCenter HS23

Brand: IBM Pages: 30

System x3950 X6

Brand: IBM Pages: 53

eserver xSeries 440

Brand: IBM Pages: 34

Brand: ACTi Pages: 15

DECT Server 2500

Brand: SpectraLink Pages: 27

Brand: Artesyn Embedded Technology Pages: 2

Disk On-line Server NAS-2100

Brand: QNAP Pages: 112

Brand: Axis Pages: 10

Brand: Planet Pages: 141

G4-Apex-ENTERPRISE-HW

Brand: Viavi Pages: 8

Brand: Gigabyte Pages: 152

Brand: Supermicro Pages: 82

Brand: Oracle Pages: 92

Brand: Gigabyte Pages: 138

Brand: IBM Pages: 68

Brand: IBM Pages: 622

Brand: IBM Pages: 233

MAXserver 1608A

Brand: NBase-Xyplex Pages: 164

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands