Lenovo ThinkAgile VX 4-Socket 4U Certified Node User Manual Download Page 131 | Manualshive

Page: 131 / 296

background image

Watch the procedure

. A video of the replacement process is available:

•

•

Figure 63. Fan installation

Step 1. Align the fan with its opening in the front of the chassis and insert, making sure that the rails on the

fan fit into the slots in the fan opening.

Step 2. Push the fan into chassis until it stops and the latch engages.

If you are done performing installation or maintenance procedures at the front of the chassis, install the front
cover. See “Install the front cover” on page 132.

Fan cage replacement

Fan cages are in the upper and lower compute trays or optional storage tray that are accessed from the front

of the server. Procedures for removing and installing fan cages in the upper and lower trays are different.

Remove a fan cage (upper tray)

The upper fan cage is in the upper compute tray or optional storage tray that is accessed from the front of

the server. After removing the upper tray, turn it upside down, press the fan cage releases, and pull the fan

cage toward the front of the tray to remove it; then, disconnect the fan cage electrical connector.

S002

CAUTION:
The power-control button on the device and the power switch on the power supply do not turn off the
electrical current supplied to the device. The device also might have more than one power cord. To

.

Hardware replacement procedures

121

«
...
129
130
131
132
133
...
»

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Reviews:

No comments

Related manuals for ThinkAgile VX 4-Socket 4U Certified Node

Brand: Rack Solutions Pages: 8

Brand: TYAN Pages: 170

Brand: Buffalo Pages: 80

Brand: AXIOMTEK Pages: 58

Brand: IBM Pages: 220

x3350 - System - 4192

Brand: IBM Pages: 98

x3500 - System - 7977

Brand: IBM Pages: 124

Brand: IBM Pages: 106

x3200 - System M3 - 7328

Brand: IBM Pages: 100

System x3400 Type 7975

Brand: IBM Pages: 124

System x3300 M4

Brand: IBM Pages: 470

System x iDataPlex dx360

Brand: IBM Pages: 26

Brand: King Pigeon Pages: 19

Aspire EASYSTORE H341

Brand: Acer Pages: 59

Aspire EASYSTORE H341

Brand: Acer Pages: 74

Aspire EasyStore Series

Brand: Acer Pages: 148

Aspire easyStore H340

Brand: Acer Pages: 68

Altos EasyStore

Brand: Acer Pages: 169

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands