Lenovo ThinkAgile VX 4-Socket 4U Certified Node User Manual Download Page 130 | Manualshive

Page: 130 / 296

background image

Figure 62. Fan removal

Step 1. Press the fan handle inward toward the center of the server to release the latch; then, pull the fan

forward halfway (see Figure 62 “Fan removal” on page 120), and wait 10 seconds.

Step 2. Pull the fan forward and out of the server. The fan is connected to the fan handle via a hinge and

the fan will flop downward when it is removed from the server.

To maintain system cooling, all fans must be installed in the server during operation.

If you are instructed to return the fan, follow all packaging instructions, and use any packaging materials for
shipping that are supplied to you.

Install the fan

Insert the fan in the front of the chassis; then, push it in until it stops and the latch engages. Fans are hot-

swap devices that can be installed while the server is powered on.

S017

CAUTION:
Hazardous moving fan blades nearby. Keep fingers and other body parts away.

Note:

The ThinkAgile VX7820 Appliance/VX 4U Certified Node supports two types of internal hot-swap fan

(a 16K fan and a 19K fan). Make sure that the fan being installed is the same type as the fan that was
removed. Different fan types cannot be mixed within a system.

Complete the following steps to install a fan:

120

User Guide for ThinkAgile VX7820 Appliance, ThinkAgile VX 4-Socket 4U Certified Node

«
...
128
129
130
131
132
...
»

Summary of Contents for ThinkAgile VX 4-Socket 4U Certified Node









































































































































































































































































































Reviews:

No comments

Related manuals for ThinkAgile VX 4-Socket 4U Certified Node

88631SU - System x3850 - 8863

Brand: IBM Pages: 90

Brand: Cobalt Digital Inc Pages: 218

Brand: IBM Pages: 106

FusionServer CH242 V5

Brand: xFusion Digital Technologies Pages: 61

UltraNEXUS-HD X5

Brand: Leightronix Pages: 5

NPort IA5250I/5250I-T Series

Brand: Moxa Technologies Pages: 2

Brand: Axel Pages: 28

Brand: BlueBroadcaster Pages: 21

ReadyNAS 3220 Series

Brand: NETGEAR Pages: 4

SUPERSERVER 2048U-RTR4

Brand: Supermicro Pages: 152

Brand: Intel Pages: 32

InterServe 600 Series

Brand: Intergraph Pages: 104

BullSequana Edge nano

Brand: Atos Pages: 29

SuperServer 1019D-FRN8TP

Brand: Supermicro Pages: 126

Brand: Asus Pages: 186

SUPERSERVER 7045W-NTR+

Brand: Supero Pages: 146

Brand: Bosanova Pages: 2

Brand: Bosanova Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands