manualshive.com logo in svg

Lenovo System x3650 M4 HD, Installation And Service Manual

Share
Download
Lenovo System x3650 M4 HD Installation And Service Manual Download Page 299

Installation tool

Microprocessor

Figure 215. Installation tool removal

Step 9.

Install the new microprocessor (see “Replacing a microprocessor and heat sink” on page 287).

Attention:

If you are replacing a microprocessor, use the empty installation tool that comes with

the new microprocessor to remove the microprocessor.

Step 10. If you do not intend to install a microprocessor on the socket, install the socket cover on the

microprocessor socket.

Attention:

The pins on the socket are fragile. Any damage to the pins may require replacing the

system board.

If you are instructed to return the microprocessor, follow all packaging instructions, and use any packaging
materials for shipping that are supplied to you.

Replacing a microprocessor and heat sink

The following notes describe the type of microprocessor that the server supports and other information that
you must consider when you install a microprocessor and heat sink.

• Microprocessors are to be installed only by trained technicians.

Important:

Always use the microprocessor installation tool to install a microprocessor. Failing to use

the microprocessor installation tool may damage the microprocessor sockets on the system board. Any
damage to the microprocessor sockets may require replacing the system board.

• Be extremely careful, the microprocessor socket contacts are very fragile. Do not touch the

microprocessor socket contacts. Contaminants on the microprocessor contacts or microprocessor socket
contacts, such as oil from your skin, can cause connection failures between the contacts and the socket.

• Do not allow the thermal grease on the microprocessor and heat sink to come in contact with anything.

Contact with any surface can contaminate the thermal grease and the microprocessor socket.

• Do not use any tools or sharp objects to lift the locking levers on the microprocessor socket. Doing so

might result in permanent damage to the system board.

• Each microprocessor socket must always contain either a socket cover or a microprocessor and heat sink.

• Be sure to use only the installation tools provided with the new microprocessor to remove or install

the microprocessor. Do not use any other tool.

• When installing multiple microprocessors, open one microprocessor socket at a time to avoid damaging

other microprocessor socket contacts.

Chapter 6

.

Removing and replacing components

287

Summary of Contents for System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands