background image

1) There are too many obstacles near the charging dock,  please place the charging dock in an open area.
2) Robot is too far away from the charging dock. Please try to place Robot near the charging dock.

1) The dust bin is full please empty and clean it.
2) The filter is clogged, please clean or replace it.
3) The main brush is entangled by something, please clean it.

1) When Wi-Fi signal is poor, please make sure the Robot is within the good Wi-Fi coverage.
2) Wi-Fi connection is abnormal, please reset Wi-Fi and download the latest phone App to try to 
connect them again.
3) incorrect password input.
4) The router is a 5G band. However, this robot only supports 2.4G band.

Problem types

Unable to power on

Unable to charge

Unable to go back to charge

Abnormal behavior

Abnormal noise during cleaning

The cleaning ability 
declines or dusting

Cannot be connected to Wi-Fi

Scheduled Cleaning mode is invalid

Does the robot vacuum consume 
power when it is on the charging dock?

Does robot vacuum need to charge for 
16 hours for the first three times uses?

Causes and solutions

1) When the battery is running low, please place Robot on the charging dock and align it with the charging 
electrode plates and Robot will power on automatically (when it’s completely out of power, Robot needs to be 
charged for a while before it powers on automatically)
2)Ambient temperature is too low or too high (below O°C/32°F or above 50°C/120°F), please use this product 
in temperature ranging from O°C/32°F to 40°C/104°F.

1) Please remove robot vacuum and check whether the charging dock indicator light is on. Make sure both of 
the charging dock and power adapter are all plugged in.
2) Poor contact, please clean up the electric shock on the charging dock and the charging electrod shock on 
the Robot.

Hold power key for seconds to shutdown and push to restart

The main brush, side brush orwheel may be entangled by something, please shutdown and clean it.

Insufficient power! The scheduled time cleaning can only be started when the remaining battery capacity 

3O%.

The power consumption is very low while Robot is charging, which helps to keep the battery at its 
best performance.

No need

because Lithium battery can be charged and used it any  time

.

21

Frequently Asked Questions (FAQ)

Summary of Contents for Robotic































Reviews: