manualshive.com logo in svg

Lenovo Flex System x220, Installation And Service Manual

The Lenovo Flex System x220 is a cutting-edge, high-performance product designed to meet all your computing needs. To ensure seamless installation and optimal service, we provide a comprehensive "Installation and Service Manual" that you can easily download for free from our website. Discover the limitless potential of the Flex System x220 today!

Share
Download
background image

Single node cannot ping the management node in a different chassis

Use the information in this section to troubleshoot a single compute node that cannot ping the Flex System
Manager management node in a different chassis on the management network.

Complete the following steps until the problem is solved:

1. Make sure that the management node is powered on and is not hung, by logging in to the management

node. If you are unable to log in from the management network, attempt to log in from the data network.
If the management node is powered on and hung, perform a virtual reseat of the management node
from the CMM.

2. Make sure that the CMM is powered on and is not hung, by pinging the CMM from the management

node:

a. If the CMM is powered on and hung, reset the CMM

b. Make sure that the IMM, the management node, and CMM are all on the same subnet.

3. Make sure that the compute node is the only one in the chassis that the management node cannot

ping. If it is not, follow the steps in “Multiple nodes cannot ping the management node in the same
chassis” on page 626. Make sure that the compute node appears on the chassis map (it might not be
fully discovered by the management node software).

4. Make sure that the IMM has acquired an IP address from the CMM by using the Setup utility on the

compute node.

Note:

If the CMM recently lost connection to the DCHP server, you must reset the IMM by using the

CMM interface so that a new IP address can be acquired.

5. Make sure that the system-management processor in each compute node has a valid IP address by

checking the chassis map of the remote chassis.

Note:

If the CMM recently lost connection to the DCHP server, you must reset the IMM by using the

CMM interface so that a new IP address can be acquired.

6. Check http://www.lenovo.com/support for any firmware updates that might apply to this issue. You can

view the release notes for a firmware update to determine the issues that are addressed by the update.

7. Check http://www.lenovo.com/support for any service bulletins that are related to network connectivity.

8. Remove the compute node and make sure that the connectors on the chassis midplane and the node

are not damaged.

9. (Trained service technician only) Check the connectors on the node and the chassis midplane to make

sure that no pins are bent.

Multiple nodes cannot ping the management node in the same chassis

Use the information in this section to troubleshoot multiple nodes that cannot ping the Flex System Manager
management node in the same chassis on the management network.

Complete the following steps until the problem is solved:

1. Make sure that the management node is powered on and is not hung, by logging in to the management

node. If you are unable to log in from the management network, attempt to log in from the data network.
If the management node is powered on and hung, perform a virtual reseat of the management node
from the CMM.

2. Make sure that the CMM is powered on and is not hung, by pinging the CMM from the management

node:

a. If the CMM is powered on and hung, reset the CMM.

b. Make sure that the IMM, the management node, and CMM are all on the same subnet.

3. Make sure that the management network port (eth0) in the management node is enabled.

626

Flex System x220 Compute Node Installation and Service Guide

Summary of Contents for Flex System x220











































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Flex System x220

Canon ColorPASS-Z5000 Getting Started preview
ColorPASS-Z5000
Brand: Canon Pages: 130
IBM Enterprise Server S80 User Manual preview
Enterprise Server S80
Brand: IBM Pages: 282
IBM Power 750 Express Hardware Announcement preview
Power 750 Express
Brand: IBM Pages: 86
IBM Netfinity 6000R User Reference Manual preview
Netfinity 6000R
Brand: IBM Pages: 218
IBM eserver xSeries 440 Troubleshooting Manual preview
eserver xSeries 440
Brand: IBM Pages: 74
IBM eserver xSeries 440 Installation Manual preview
eserver xSeries 440
Brand: IBM Pages: 98
IBM eserver xSeries 440 User Manual preview
eserver xSeries 440
Brand: IBM Pages: 84
IBM Eserver xSeries 360 Type 8686 User Reference Manual preview
Eserver xSeries 360 Type 8686
Brand: IBM Pages: 184
IBM eserver xSeries 350 Installation Manual preview
eserver xSeries 350
Brand: IBM Pages: 62
IBM eServer xSeries 135 Installation Manual preview
eServer xSeries 135
Brand: IBM Pages: 62
IBM eserver pSeries 690 User Manual preview
eserver pSeries 690
Brand: IBM Pages: 212
IBM System x3690 X5 At-A-Glance Reference Manual preview
System x3690 X5
Brand: IBM Pages: 32
IBM System x3690 X5 At-A-Glance Manual preview
System x3690 X5
Brand: IBM Pages: 33
IBM System x3690 X5 Installation And User Manual preview
System x3690 X5
Brand: IBM Pages: 180
IBM pSeries 670 Service Manual preview
pSeries 670
Brand: IBM Pages: 1032
Sun Fire X4600 Installation Manual preview
X4600
Brand: Sun Fire Pages: 66
QNAP TS-130-US User Manual preview
TS-130-US
Brand: QNAP Pages: 39
sysmik ICS-709 Installation Notes For Electrical Personnel preview
ICS-709
Brand: sysmik Pages: 2

Brands by name

Popular brands

Load more brands