background image

Lenovo B41-80
Hardware Maintenance Manual

12

Safety notice 6

DANGER

To avoid shock, do not remove the plastic cover that protects the lower part 
of the inverter card.
Afin d’éviter tout risque de choc électrique, ne retirez pas le cache en 
plastique protégeant la partie inférieure de la carte d’alimentation.
Aus Sicherheitsgründen die Kunststoffabdeckung, die den unteren Teil der 
Spannungswandlerplatine umgibt, nicht entfernen.

Per evitare scosse elettriche, non rimuovere la copertura in plastica che 
avvolge la parte inferiore della scheda invertitore.

Para evitar descargas, no quite la cubierta de plástico que rodea la parte baja 
de la tarjeta invertida.

Safety notice 7

DANGER

Though the main batteries have low voltage, a shorted or grounded battery 
can produce enough current to burn personnel or combustible materials.
Bien que le voltage des batteries principales soit peu élevé, le court-circuit ou 
la mise à la masse d’une batterie peut produire suffisamment de courant 
pour brûler des matériaux combustibles ou causer des brûlures corporelles 
graves.
Obwohl Hauptbatterien eine niedrige Spannung haben, können sie doch bei 
Kurzschluß oder Erdung genug Strom abgeben, um brennbare Materialien 
zu entzünden oder Verletzungen bei Personen hervorzurufen.

Sebbene le batterie di alimentazione siano a basso voltaggio, una batteria in 
corto circuito o a massa può fornire corrente sufficiente da bruciare materiali 
combustibili o provocare ustioni ai tecnici di manutenzione.

Aunque las baterías principales tienen un voltaje bajo, una batería 
cortocircuitada o con contacto a tierra puede producir la corriente suficiente 
como para quemar material combustible o provocar quemaduras en el 
personal.

Summary of Contents for B41-80






















































































Reviews:

Related manuals for B41-80