manualshive.com logo in svg

Lenovo 41896HU, Hardware Maintenance Manual, Page: 34 / 107

Share
Download
Lenovo 41896HU Hardware Maintenance Manual Download Page 34

30

IdeaPad Y450 Hardware Maintenance Manual

Symptom-to-FRU index

This section contains the following information:
•

  “Numeric error codes

” on page 30

•

  “Error messages 

” on page 33

•

  “Beep symptoms

” on page 36

•

 

“No-beep symptoms ” on page 36

•

 

“LCD-related symptoms” on page 37

•

  “Intermittent problems

” on page 38

•

 

“Undetermined problems” on page 38

The symptom-to-FRU index in this section lists symptoms and errors and their 

possible causes. The most likely cause is listed first, in boldface type.

Note:

 Do the FRU replacement or other actions in the sequence shown in the 

column headed “FRU or action, in sequence.” If replacing a FRU does not 

solve the problem, put the original part back in the computer. Do not replace a 

nondefective FRU.
This index can also help you determine, during regular servicing, what FRUs 

are likely to need to be replaced next.
A numeric error is displayed for each error detected in POST or system 

operation. In the displays, n can be any number.
If no numeric code is displayed, check the narrative descriptions of symptoms. 

If the symptom is not described there, go to “Intermittent problems

” on page 38. 

Note:

For a device not supported by diagnostic codes in the Lenovo IdeaPad computers, 

see the manual for that device. 

Numeric error codes

Table 1. Numeric error codes

Symptom or error 

FRU or action, in sequence 

0200

Hard disk error—The hard disk is not 

working. 

1. 

Reseat the hard disk drive

.

2. Load Setup Defaults in BIOS Setup 

Utility.

3. Hard disk drive.
4. System board.

021x

Keyboard error. 

Run interactive tests of the keyboard 

and the auxiliary input device

.

0220

Monitor type error—Monitor type does 

not match the one specified in CMOS. 

Load Setup Defaults in BIOS Setup 

Utility

.

0230

System RAM error—System RAM fails 

at offset nnnn.

1. 

DIMM

.

2. System board. 

0231

Shadow RAM error—Shadow RAM fails 

at offset nnnn.

System board

. 

Summary of Contents for 41896HU












































































































Reviews:

No comments