Lenoir LF160 Instruction Manual Download Page 4

 

Selecting the temperature 

1.Check the ironing instructions on the garment to be ironed. 
2.If the garment does not have any ironing instructions but you know the kind of fabric in question, use the chart below. 

3. Fabrics that have some kind of finish(polishing . wrinkles , contrasts….)can be ironed at the lowest temperatures. 
4.If the fabric contains several kinds of fibres ,always select the temperature applicable ,if an article contains 60% 

polyester and 40% cotton ,you must always choose the temperature corresponding to polyester and without steam. 
5. First classify the articles to be ironed according to the most suitable ironing temperature : wool with wool, cotton with 

cotton, etc. as the iron heats up as fast as it cools , start by ironing the articles requiring the lowest temperature such as 
those made of synthetic fibres . Progress towards those that require the highest temperatures. 

6.Turn the temperature control until it is in front of the appropriate signal according to the following: 

·

       position for nylon and acetate 

··

      position for wool ,silk or mixures 

···

     position for cotton or linen (steam). 

 

 
How to fill the water tank

1.

 

Unplug the iron 

2.

 

Set the steam ruler to dry ironing .  

3.

 

Fill the tank through the filling hole. 

4.

 

If you have hard water ,it is advisable to use only distilled or demineralized water. 

Do not use chemically de-limed water or perfuse

 

5.

 

Do not store the iron with water in the tank. 

 

 

HOW TO USE 

 

Steam ironing 

1.Fill the iron as described in the section “

how to fill the water tank

”. 

2. Plug the iron into the mains. 
3.Steam ironing is only possible when the highest temperatures shown on the temperature control are selected . 

Otherwise ,water may escape through the soleplate. 

4. Wait until the pilot light goes out , which indicates that the selected temperature has been reached. 

5.Turn the steam button to the required position.  
6.When the ironing is finished and during breaks in ironing , place the iron in its upright position. 

7.Disconnect the iron from the mains supply . Pour of any remaining water and leave the iron to cool off. 

Spray 

1.The spray can be used in any position, either in dry or steam ironing, as long as the water tank is filled with water. 

2.Press the spray button for this function 

NOTE : This button has to be pressed repetitively to start this function for the first time. 

Shot of steam 

Shot of steam give extra steam for removing persistent wrinkles. 

1.Place the temperature selector at the “max”position and wait until the pilot light goes out 
2.Wait for a few seconds for the steam to penetrate the fibre before pressing again. 

NOTE : For the best steam quality, do not use more than three successive bursts each time. Several pumping actions 

are needed to start this function. 

Excessive use of this feature will cause the iron to cool , ensure that the pilot light is out, before operating 
the shot of steam control 

 

 

Summary of Contents for LF160








Reviews: