manualshive.com logo in svg

Lenntech aeroQUAL, Manual, Page: 18 / 20

Share
Download
Lenntech aeroQUAL Manual Download Page 18

Status LED 

Indicator 

No power, No connection, 
controller failure 

Off – relay open 

Control Operation 

 

< Low Set Point 

Orange  (constant) – relay closed  

Within Control Band 

Green    (constant) 

> High Set Point 

Red       (constant) – relay open 

Control Status 

 

Warm Up (30 minutes) 

Green  (Slow Flash -2 sec period) 
- relay open 

Wrong Switch Setting (eg.  
low rotary > high rotary) 

Orange (Fast Flash -0.5 sec period) – 
relay open 

Sensor Failure 

Red  (Fast Flash  0.5 sec period) 
– relay open 

Switch Operation 

 

Normal operation 

Green   (constant) 

Low Switch 

Yellow  (constant) 

High Switch 

Red      (constant) 

Sensor Head Failure 

The sensor failure LED signal (red fast flash) will activate due to: 

•

Sensor Life Exceeded –

this indicates that the sensor has 

operated beyond its design life and should be replaced.

 

•

Sensor Failure-

 

the sensor head is no longer operating 

within the on-board diagnostic settings and should be 
replaced.

 

16  

Summary of Contents for aeroQUAL





















Reviews:

No comments