background image

2

Included Parts

The assembled indoor unit will include the following items:

Table 1.  Included Parts

Parts

Figure

Quantity

Parts

Figure

Quantity

Wireless controller

1

Installation instruction, 

user guide and warranty

1 ea.

Wireless control 

holder with 2 mounting 

screws

Mounting plate  

(shipped attached to the 

back of the indoor unit)

1

Batteries (AAA)

2

Mounting plate securing 

screws

5

Return Air Filters  

(Shipped installed in 

indoor unit.)

Plastic screw anchors

5

Assembled Outdoor Unit includes the following items:

Parts

Figure

Quantity

Parts

Figure

Quantity

Drain connector

1

Seal ring

1

WARNING

The clean Air Act of 1990 bans the intentional venting of 

refrigerant (CFCs, HCFCs, and HFCs) as of July, 1992. 

Approved methods of recovery, recycling or reclaiming 

must be followed. Fines and/or incarceration may be 

levied for non­compliance.

CAUTION

As with any mechanical equipment, contact with sharp 

sheet metal edges can result in personal injury. Take 

care while handling this equipment and wear gloves 

and protective clothing.

IMPORTANT

All illustrations in this instruction are typical and do 

not always represent the exact appearance of the 

equipment. 

IMPORTANT

The  compressor  in  this  unit  contains  PVE 

oil  (Polyvinylether).  PVE  oil  is  formulated  for 

 

hydrofluorocarbon  (HFC)  refrigerants,  such  as  HFC-

410A,  which  this  system  contains.  While  it  may  have 

some miscibility properties with mineral­based oil and 

POE oil (Polyolester), it is not recommended to mix PVE 

oil with any other type of refrigerant oil.

Summary of Contents for MWHB Series





















Reviews: