background image

5

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

LENNOX HEARTH PRODUCTS  •  MERIT

® 

 SERIES B-VENT GAS FIREPLACES  •  MODELS MLBV-35, MLBV-40  •  INSTALLATION INSTRUCTIONS

COLd CLIMATE INSULATION

For  cold  climate  installations,  seal  all  cracks 

around  your  appliance  with  noncombustible 

material  and  wherever  cold  air  could  enter 

the room. It is especially important to insulate 

outside chase cavity between studs and under 

floor on which appliance rests, if floor is above 

ground level. Gas line holes and other openings 

should  be  caulked  or  stuffed  with  unfaced 

fiberglass  insulation.  Check  local  codes  for 

additional requirements.

If the fireplace is being installed on a cement 

slab in cold climates, a sheet of plywood or 

other raised, insulated platform can be placed 

underneath  to  prevent  cold  transfer  to  the 

fireplace and into the room. It also may help 

to sheetrock the inside surfaces and/or tape 

for maximum air tightness. 

LOCATION

In  selecting  the  location,  the  aesthetic  and 

functional  use  of  the  appliance  are  primary 

concerns.  However,  vent  system  routing  to 

the exterior and access to the fuel supply are 

also important.  

Due  to  high  temperatures,  the  appliance 

should be located out of traffic and away from 

furniture and draperies (Figure 3). 

En  raison  des  températures  élevées, 

l’appareil  devrait  être  installé  dans  un 

endroit où il y a peu de circulation et loin 

du mobilier et des tentures (Figure 3).

The location should also be free of electrical, 

plumbing  or  other  heating/air  conditioning 

ducting.

These appliances are equipped with an inte-

gral combustion air door and actuator arm.  

Combustion air kits are optional and must be 

installed before removing the securing screw 

allowing the movement of the combustion air 

actuator arm 

(see Step 5 on Page 14)

.

Be  aware  that  this  is  a  heat-producing  ap-

pliance.  Objects  placed  above  the  unit  are 

exposed to elevated temperatures.

The appliance should be mounted on a fully 

supported  base  extending  the  full  width  and 

depth of the unit. The appliance may be located 

on or near conventional construction materials. 

However, if installed on combustible materials, 

such as carpeting, vinyl tile, etc., a metal or 

wood barrier covering the entire bottom surface 

must be used.

These appliances may be used for bedroom 

installations in the United States and are listed 

accordingly.  These units may not be installed 

in bedrooms in Canada.

Figure 3: Typical Locations

Note: When the unit is installed with one side 

flush with a wall, see Figure 5 on Page 7.

Typical Locations

Summary of Contents for MBLV-35NE





























Reviews: