background image

6

Installation of these appliances are approved for installation in New York 

City in the US state of New York.

(Massachusetts Approval #G1-1105-11)

These appliances are approved for installation in the US state of Mas-

sachusetts if the following additional requirements are met:

•  Install this appliance in accordance with Massachusetts Rules and 

Regulations 248 C.M.R. Sec. 5.08 2(a) through 2(e).

•  Installation and repair must be done by a plumber or gas fitter licensed 

in the Commonwealth of Massachusetts.

•  The flexible gas line connector used shall not exceed 36 inches (92 

centimeters) in length.

•  The individual manual shut-off must be a T-handle type valve. 

Massachusetts Horizontal Vent Requirements 

In the Commonwealth of Massachusetts, horizontal terminations installed 

less than seven (7) feet above the finished grade must comply with the 

following additional requirements:

•  A hard wired carbon monoxide detector with an alarm and battery 

back-up must be installed on the floor level where the gas fireplace 

is installed.  The carbon monoxide detector must comply with NFPA 

720, be ANSI/UL 2034 listed and be ISA certified.

•  A metal or plastic identification plate must be permanently mounted to 

the exterior of the building at a minimum height of eight (8) feet above 

grade and be directly in line with the horizontal termination.  The sign 

must read, in print size no less than one-half (1/2) inch in size, GAS 

VENT DIRECTLY BELOW.  KEEP CLEAR OF ALL OBSTRUCTIONS.

NEW YORK CITY, NEW YORK (MEA)

COMMONWEALTH OF MASSACHUSETTS REQUIREMENTS

       WARNING 

Failure to comply with the installation and operating 

instructions provided in this document will result in 

an improperly installed and operating appliance, 

voiding its warranty.  Any change to this appliance 

and/or its operating controls is dangerous.  Improper 

installation or use of this appliance can cause seri-

ous injury or death from fire, burns, explosion or 

carbon monoxide poisoning.

       WARNING 

Do not place clothing or other flammable materials 

on or near this appliance.

       

AVERTISSEMENT

Surveiller  les  enfants.    Garder  les  vêtements,  les 

meubles, l'essence ou autres liquides à  vapeur inflam-

mables lin de l'appareil.

WARNING: This appliance must be properly connected to a venting 

system.  Operation of this gas appliance when not connected to 

a properly installed and maintained venting system can result in 

carbon monoxide (CO) poisoning and possible death.

Carbon  Monoxide  Poisoning:  Early  signs  of  carbon  monoxide 

poisoning are similar to the flu with headaches, dizziness and/or 

nausea. If you have these signs, obtain fresh air immediately. Have 

the appliance serviced by a qualified technician as it may not be 

operating correctly.  Some people are more affected by carbon 

monoxide  than  others.  These  include  pregnant  women,  people 

with heart or lung disease or anemia, those under the influence of 

alcohol, and those at high altitudes.

In  selecting  the  location,  the  aesthetic  and  functional  use  of  the 

appliance are primary concerns. However, vent system routing to the 

exterior and access to the fuel supply are also important. Consider-

ation should be given to traffic ways, furniture, draperies, etc., due 

to elevated surface temperatures. 

       WARNING 

Children and adults should be alerted to the hazards 

of high surface temperatures. Use caution around 

the appliance to avoid burns or clothing ignition. 

Young children should be carefully supervised when 

they are in the same room as the appliance.

Note: An Optional Screen Panel for the glass is avail-

able (see Homeowners Manual for ordering informa-

tion).

LOCATION

Considerations Should Include:

• Existing Chimneys

• Aesthetic Considerations

• Roof Design (Rafter Locations and Roof Pitch)

• Room Traffic

• Proximity to Combustibles

• Proximity for Optimum Heat Transfer

• Electrical Wiring (if optional blower is installed)

The  installation  of  this  stove  will  require  some  research.  Once  your 

options  are  determined,  consult  with  your  local  building  department 

who will be able to give you the necessary installation requirements for 

your area (Is a building permit required?, Rooms where installation may 

not be allowed?, etc.). 

Summary of Contents for CI1500DVF Series



























Reviews: