background image

4

460989001B 

CPU status LED D45 possible module error conditions for LED Normal and 
Series 2 modes:

Mounting

The SDC can be mounted in the LNL-AL400ULX or LNL-AL600ULX-
4CB6 and the LNL-CTX or LNL-CTX6 enclosure using the Universal 
Mounting Plate (UMP) LNL-CONV-U2. The universal mounting plate can 
hold up to two (2) LNL-1300-U modules.

Mounting the SDC in the LNL-AL400ULX and LNL-CTX

Mounting the SDC in the LNL-AL600ULX-4CB6 or LNL-CTX6

Error condition

Flashing 
pattern

Description

No valid 
application 
firmware

3 Red, 
2 Green

The module is not operational. 
Firmware must be loaded using a 
console, e.g. HyperTerminal with 
Xmodem.

Boot loader waiting 
on firmware file

3 Red, 
1 Green

Console boot loader is waiting on 
start of firmware file.

Boot loader loading 
firmware file

2 Red, 
2 Green

Console boot loader is loading a 
firmware file.

Invalid EFL file

1 Red, 
2 Green

The EFL specified to be loaded 
using the console loader is not a 
valid EFL file.

Invalid Xmodem 
packet

1 Red, 
1 Green

The console loader received an 
invalid Xmodem packet and 
terminated the firmware 
download operation.

Invalid Application 
firmware for 
module CPU

3 Red, 
0 Green

The module is not operational. 
Application firmware loaded on 
the module will not run properly. 
Requires new firmware be loaded 
using the console boot loader or 
the module must be returned for 
repair.

Invalid Boot 
firmware for 
module CPU

2 Red, 
3 Green

The module is not operational. 
Boot loader firmware loaded on 
the module will not run properly. 
The module must be returned for 
repair.

Firmware update 
failed

1 Red, 
3 Green

Firmware update operation was 
unsuccessful. Retry and if it fails 
continuously, load a different 
firmware file.

No valid primary 
firmware copy

3 Green, 
2 Red

The firmware flash contains 2 
copies of the application 
firmware. The primary copy is 
not valid so the backup copy will 
be loaded into the primary copy 
and executed.

No valid backup 
firmware copy

3 Green, 
1 Red

The firmware flash contains 2 
copies of the application 
firmware. The backup copy is not 
valid so the primary copy will be 
loaded into the backup copy.

No valid 
manufacturing 
parameters

3 Green, 
0 Red

The manufacturing parameters 
which include the serial number, 
etc. are invalid. The module must 
be returned for repair.

Summary of Contents for LNL-1300-U









Reviews: