Lenel DirecDoor Installation Manual Download Page 27

Page: 27 / 90

DirecDoor Installation Guide

CHAPTER 4

DirecDoor Board

DirecDoor Board Overview and Layout

The DirecDoor board provides network capabilities in one board.

The following are some product highlights:

•

Supports Ethernet networks.

•

Supports the dual Network Interface Card (NIC).

Note:

The DDSDC does not support the dual Network Interface Card (NIC).

•

Supports the following network protocols: DHCP and UDP.

•

Provides nonvolatile storage referred to as persistent mode of operation. This means a faster reset
recovery and allows for host-less operation.

•

Utilizes a 32-bit platform which provides better response times and higher capacity.

•

Allows for remote diagnostics.

•

Provides a browser-based configuration tool. Refer to

Controller Firmware Tools

on page

Refer to the

System Administration User Guide

for configuration of this board within the access

control software.

The layout of the DirecDoor board is shown on the following page.

Summary of Contents for DirecDoor



























































































Search results

Summary of Contents for DirecDoor

Reviews:

Related manuals for DirecDoor

Brands by name

Popular brands

Lenel DirecDoor, Installation Manual

Search results

Summary of Contents for DirecDoor

Reviews:

Related manuals for DirecDoor

Brands by name

Popular brands