Leitronic AG EA-8-WRL868, Use Instruction, Page: 20 / 40

20
6.7.3 Listening-in connection
Possible tone-dialling commands during the listening-in connection
DTMF => Every valid command will be signalled
0 Terminate phone connection and acknowledge alarm
1 Switching to hands-free mode and restart connection time-out
2 Repeat announcements ( Individual message / Cause of alarm)
3 Restart connection time-out (2 minutes)
4 Deactivate output (i.e. switching off 230VAC load)
5 Announcement of current supervision mode as well as condition of the output
6 Activate output (i.e. switching on 230VAC load)
7 Change to inactive supervision mode (I, II, III)
8 Terminate phone connection without acknowledgment
9 Change to active supervision mode (I, II, III) => All monitoring functions re-activated
* * 0 Announcement of calling number sequence
* * n Announcement of calling number n ( n = 1..9)
Following tone-dialling command can be used for remote programming, provided the programming is not
blocked (

section 9.8.1)
* * # Trigger an alarm for test reasons

Cause of alarm announcement "alarm due to programming"
* * n * followed by the new calling number Announcement and change of calling number n ( n = 1..9)
* * # # Record individual message => according to section 5.3.1.
6.7.4 Hands-free connection
The commands during hands-free connection are identical to the commands by listening in connection, by press
DTMF 1 .
Important notes:

Hands-free connection must be terminated using DTMF 0 or 8 . Otherwise a busy tone signal
appears until phone connection is terminated due to time-out.

By selecting hands-free connection an activated siren (optionally) is automatically deactivated. If
requested, the siren can be activated or deactivated by DTMF 6 or 4 .
6.7.4.1 Adjustment of hands-free volume
During hands-free connection you can increase volume by pressing local key
# .
or decrease by pressing locale
key * . . Level can be adjusted in fifteen steps (1dB each) and remains stored.
6.7.5 Acknowledge alarm / Terminate connection
A called party can choose between acknowledgment by pressing DTMF 0 or passing on alarm to next party
in calling number sequence by pressing DTMF 8 .
Important notes:

There is no alarm repetition, if an alarm is triggered by pressing any key of the alarm unit (test call).

An alarm can be confirmed and terminated by pressing key
0 .
of the alarm unit or by pressing the
wireless emergency button for a second time.

If the alarm is programmed to a pager, the called person can confirm alarm during remote-access
after dialling-in.
6.8 Alarm repetition
If an alarm has not been acknowledged by passing all the calling numbers in the sequence, a number of alarm
repetitions can be programmed (

section 9.2). Factory setting: two alarm repetitions.
6.9 Test call
If alarm unit is switched to ON it is possible to start a test call as follows:
1. Select calling number by pressing key
<n>
( n =
1 .
..
9
)

Announcement: „Calling number
<n>
“ => If selected calling number is not programmed the
message “Error” will be announced and the first calling number will be dialled instead
2. Wait until hands-free connection is established and speak
3. Terminate phone connection by pressing
0 .
or slide function switch to OFF
Notes:

After two minutes phone connection will automatically terminate if called party does not give any tone-
dialling commands (i.e. called subscriber can disconnect using DTMF 0 or restart timer using DTMF 3 ).

During inactive waiting period after power on key 9 . and 7 . activate or deactivate the monitoring of the
supervision. Key
5 .
starts the announcement of the current supervision mode (

section 6.3.1)

The volume of hands-free connection can be adjusted as described in section 6.7.4.1