Leitch DMX-3901-A Installation And Operation Manual Download Page 6

Page: 6 / 64

DMX-3901-A Installation and Operation Manual

iii

Purpose ........................................................................................... vii
Audience ........................................................................................ vii
Revision History ............................................................................ vii
Writing Conventions ..................................................................... viii
Obtaining Leitch Documents ........................................................ viii

Unpacking the Module ........................................................................... ix
Safety Standards and Compliances ........................................................ ix

Safety Terms and Symbols ...............................................................x

Trademarks and Copyrights .....................................................................x
Warranty Information ..............................................................................x

........................................................................................................ xi

Chapter 1: Introduction

Overview ..................................................................................................1
Product Description ..................................................................................2

Main Features ...................................................................................2

Front and Back Modules ..........................................................................3

Front Module ....................................................................................3
Back Module .....................................................................................4
Plug-In Adapter .................................................................................5

Signal Flow ..............................................................................................6

Chapter 2: Installation and Removal

Overview ..................................................................................................7
Packing List ..............................................................................................8
Installing DMX-3901-A Modules ............................................................8
Removing DMX-3901-A Modules ..........................................................8

Summary of Contents for DMX-3901-A

































































Search results

Summary of Contents for DMX-3901-A

Reviews:

Leitch DMX-3901-A, Installation And Operation Manual, Page: 6 / 64

Search results

Summary of Contents for DMX-3901-A

Reviews: