manualshive.com logo in svg

Leister UNIPLAN 300, Manual

Share
Download
Leister UNIPLAN 300 Manual Download Page 23

23

39

40

44

43

42

41

UNIPLAN 300 control panel

Overview of the UNIPLAN 500 control panel

39. Drive "On/Off" key with LED status display

40. Heating "On/Off" key with LED status display

41. Minus key

42. Confirm button

43. Plus key

44. Display fields

 

The actual values are displayed in large font 

and the setpoint values in small font. The cursor is 

located  

 

on the left-hand side and the parameter unit  

 

on the right-hand side.

Symbols

LED status display
Heating

The LED display on the 

Heating "On/Off" key (40)

 shows the respective condition of the heating.

Symbol

Meaning

Cool down mode

Symbol for the cool-down process

Warning message and error message

 See the Chapter Warning and error messages (UNIPLAN 300) 28 [11]

Maintenance 

 See the Chapter Maintenance (UNIPLAN 300) 28 [12]

LED status

Heating On/Off (40)

Condition

LED off

Heating is turned off.

LED flashes green

Heating is turned on. Temperature is outside the tolerance range.

LED continuously green

Heating is turned on. Temperature is within the tolerance range.

Summary of Contents for UNIPLAN 300
































Reviews:

No comments

Brands by name

Popular brands

Load more brands