LEHR LP9.9 EL Operator'S Manual Download Page 27

LEHR

 | 

ALL RIGHTS RESERVED 2013-2014

25

The limited warranty set forth below is given by LEHR with respect to new merchandise purchased and used 
in the United States and Canada, its possessions and territories.  LEHR warrants to the original purchaser 
that each new LEHR brand outboard is free from defects in material and workmanship and agrees to repair 
or replace under this warranty any defective product or attachment as follows from the original date of 
purchase.

3 YEARS -- Parts and Labor.
90 DAYS -- Parts and Labor, when used for income producing purposes.
30 DAYS -- Parts and Labor, if used for rental purposes.

This warranty is not transferable and does not cover damage or liability caused by improper handling, 
improper maintenance, or the use of accessories not speci

¿

cally recommended by LEHR for this product. 

In addition, it does not cover any product that has been subject to misuse, neglect, negligence, or accident, 
or has been operated in any way contrary to the operating instructions speci

¿

ed in this operator’s manual. 

Additionally, this warranty does not cover tune-ups, spark plugs, carburetor adjustments, starter pulley or  
parts that will wear and require replacement with reasonable use during the warranty period. This warranty 
does not cover pre delivery setup or normal adjustments explained in the instruction manual.  Shipping of
parts is not the responsibility of LEHR.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY HAVE OTHER RIGHTS WHICH 
VARY FROM STATE TO STATE.  NO CLAIMS FOR CONSEQUENTIAL OR OTHER DAMAGES WILL BE 
ALLOWED, AND THERE ARE NO OTHER EXPRESS WARRANTIES EXCEPT THOSE EXPRESSLY 
STIPULATED HEREIN.  SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED 
WARRANTY LAST OR THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL 
DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSION MAY NOT APPLY TO YOU.  

LEHR does not extend any warranty for products sold or exported outside of the United States or Canada, 
its possessions and territories, except those sold through LEHR’s authorized channels of export distribution.  
The policy of LEHR is to continuously improve its products.  Therefore, LEHR reserves the right to change, 
modify, or discontinue models, designs, speci

¿

cations of all products at any time without notice or obligation 

to any purchaser. 

HOW TO OBTAIN SERVICE: Warranty service is available, with proof of purchase through your local 
authorized service dealer.  To locate the dealer in your area, visit our website at www.golehr.com or call 
1-866-941-LEHR or write to 8922 Ellis Ave. LA, CA 90034.

CALIFORNIA EMISSIONS/EPA CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OBLIGATIONS  

The California Air Resources Board, the Environmental Protection Agency and LEHR, Inc. are pleased to 
explain the emissions control system’s warranty on your 2013 and later marine engine.  In California and 
the 49 states, new equipment that use marine engines must be designed, built, and equipped to meet the 
State’s stringent anti-smog standards.  LEHR, Inc. must warrant the emissions control system on your 
small off-road engine for the period listed below provided there has been no abuse, neglect or improper
maintenance of your engine.  

Your emissions control system may include parts such as: carburetors or fuel injection system, ignition 
system, catalytic converters, fuel tanks, valves, filters, clamps, connectors, and other associated 
components.  Also, included may be hoses, belts, connectors, sensors, and other emission-related 
assemblies.  

Where a warrantable condition exists, LEHR will repair your marine engine at no cost to you including 
diagnosis, parts and labor.  

MANUFACTURER’S WARRANTY COVERAGE:  
This emissions control system is warranted for ten years.  If any emissions-related part on your equipment 
is defective, the part will be repaired or replaced by LEHR.  

OWNER’S WARRANTY RESPONSIBILITIES:  

‡

 As the marine engine owner, you are responsible for performance of the required maintenance listed in 

  your owner’s manual.  LEHR recommends that you retain all receipts covering maintenance on your 
  marine engine, but LEHR cannot deny warranty solely for the lack of receipts or your failure to ensure 
  the performance of all scheduled maintenance. 

‡

 As the marine engine owner, you should however be aware that LEHR may deny you warranty coverage if 

  your marine engine or a part has failed due to abuse, neglect, or improper maintenance or unapproved 
  modifications. 

‡

 You are responsible for presenting your marine engine to a LEHR service center as soon as the problem 

  exists.  The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days.  
  If you have a question regarding your warranty coverage, you should contact LEHR at 1-866-941-LEHR.  

M

ANUFACTURER’S LIMITED WARRANTY

Summary of Contents for LP9.9 EL































Reviews: