LEHR LP9.9 EL Operator'S Manual Download Page 26

Page: 26 / 30

LEHR

SPECIFICATIONS

ENGINE TYPE

WATER COOLED 4-CYCLE

DISPLACEMENT

12.94 cu. in (212 cc)

*ALL SPECIFICATIONS ARE BASED ON THE LATEST PRODUCT INFORMATION AT THE TIME OF PRINTING.

WE RESERVE THE RIGHT TO MAKE CHANGES AT ANY TIME WITHOUT NOTICE.

BORE X STROKE

2.29 in X 1.69 in (56 mm X 43 mm)

GEAR RATIO

2.08 (27/13)

GEAR SHIFT

F – N – R

TRANSOM HEIGHT

SHORT SHAFT 15 in (381 mm)

MAX OPERATING R.P.M.

4500 - 5500 R.P.M.

IDLE SPEED

1000-1200 R.P.M.

IGNITION TYPE

ELECTRONIC CDI

IGNITION SWITCH

TETHER

VALVE CLEARANCE IN and EX (COLD)

SPARK PLUG GAP

0.020-0.024 in (0.5-0.6 mm)

LUBRICATION OIL TYPE

CRANKCASE OIL CAPACITY

0.85 US qt. (0.8L)

FUEL

STARTER

PULL CHORD AUTO REWIND AND/OR PUSH BUTTON SWITCH

PROPANE

4 STROKE 10W-30

SPARK PLUG TORQUE SPEC

18.4 ft.

lb. (25.0 N

GEAR OIL TYPE / CAPACITY

SPARK PLUG TYPE

NGK BR6HS

POWER

9.9 hp (7.2 kW)

WEIGHT

87.7 lbs (39.8 kg) (S), 91.7 lbs (41.6 kg)(L)

MODELS LP 9.9

(S) SHORT SHAFT
(L) LONG SHAFT
(ES) ELECTRIC START, TILLER, SHORT SHAFT
(EL) ELECTRIC START, TILLER, LONG SHAFT
(ERS) ELECTRIC START,REMOTE STEERING, SHORT SHAFT
(ERL) ELECTRIC START, REMOTE STEERING, LONG SHAFT

INTAKE: 0.0059-0.0079 in (0.15-0.20mm)

EXHAUST: 0.0079-0.0098 in (0.20-0.25mm)

HYPOID GEAR OIL SAE#90 0.26 US qt. (0.250L)

97.7 lbs (44.3kg) (ES, ERS), 101.7 lbs (46.1 kg)(EL, ERL)

LONG SHAFT 20 in (508 mm)

PROPELLER NUT TORQUE SPEC

12.5 ft

lb (17.0 N

OIL DRAIN PLUG TORQUE SPEC

17.7 ft

lb (24.0 N

Summary of Contents for LP9.9 EL






























Search results

Summary of Contents for LP9.9 EL

Reviews:

LEHR LP9.9 EL, Operator'S Manual, Page: 26 / 30

Search results

Summary of Contents for LP9.9 EL

Reviews: