LEHMANN Primary Controller Operating Instructions Manual Download Page 9

BD

A Primar

y Con

tr

oller / Sec

ondar

y Con

tr

oller 22-02-17 (GB)

99

1

   Connections for connecting cables coming  

from locks

 

 

Input power cable

 

  

Output power connection cable for  
supplying a controller

  

Input / output connection cable for  
connecting additional controllers (RS485)

  

LAN / Ethernet port for connection to the  
customer‘s network (only with primary controller)

 

USB type A port (only with primary controller)

 

Mini USB

 

Relais for future functions

 

  

Opt.-In (e.g. for signal contact of a UPS unit)

  

RFID eading field (only with primary controller)

CABLE ROUTING FROM LOCK TO CONTROLLER

 (RECOMMENDATION)

There are different ways to route the cable from the lock to the controller. The instructions for inserting the connecting 
cable into the lock as well as the instructions for assembling the lock in the cabinet can be found in the operating 
instructions „Captos MIFARE / Captos iCharge MIFARE“. 
We recommend cabling the locks in such a way that individual cabinet elements can be exchanged (see figure: Cabling 
on the cabinet module). It should be taken into account that in the event of a cabinet exchange, there is sufficient cable 
length to pull the cabinet out of its installation position and then to loosen the cables from the locks in the next step. 
For example, couplings (cable connection sockets) can be used to remove or replace individual cabinets from the cabinet 
wall without great effort. Alternatively, a correspondingly large cable loop can be laid with continuous cabling. It should 
be absolutely avoided that cables are subjected to tensile stress during normal operation or through installation and 
removal. It is recommended that cables are clearly labeled at both ends, for example according to the cabinet number. 
This simplifies the service case and any troubleshooting. 
Cable ends that are too short can mean that the plug connectors of the locks can no longer be reached and damage-free 
dismantling is no longer possible.
The locks should be connected with as little cable as possible. Wall mounting options are available on the controller 
housings. When cabling and placing the controller and power supply unit, make sure that these components are 
accessible in the event of a defect or power failure. A defect in the power supply unit or a controller can mean that the 
locks connected there can no longer be operated. Access to power supply units and controllers must be ensured for 
maintenance work and in the event of a defect.

Figure:  
Cabling on the cabinet module

Summary of Contents for Primary Controller

















Reviews: