background image

Wattstopper

 

®

Vacancy Sensor Switch (v2)
Interrupteur de détecteur d’inoccupation (v2)
Interruptor del sensor de vacantes (v2)

Installation Instructions • Instructions d’Installation • Instrucciones de Instalación

No: 24218 – 07/20  rev. 2

Catalog Number • Numéro de Catalogue • Número de Catálogo: CS-50

Country of Origin: Made in China • Pays d’origine: Fabriqué en Chine • País de origen: Hecho en China

SPECIFICATIONS

Voltage .................................................................... 120VAC, 60Hz
Load (Single Pole Circuit)
 

Incandescent, Fluorescent, E-Ballast, or LED ...... 0-600 Watt 

Fan motor ..............................................................................1/6 hp
Time Delay .............................................30 seconds to 30 minutes
Environment ........................................................... Indoor use only
Operating Temperature ...........................32° to 131°F (0° to 55°C)
Humidity .................................................95% RH, non-condensing
Storage Temperature .............................. 5F to 158F (-15C to 70C)
Tools Needed
Insulated Screwdriver
Wire Strippers

Cover plate not included

DESCRIPTION AND OPERATION

The CS-50 Vacancy Sensor is designed to replace a standard light or fan switch. The sensor uses passive infrared technology to sense 

human motion in a space and turn the light OFF when the room is vacant. It is ideal for applications where there is a direct line of sight 

from the sensor to the room. 
Like a standard switch, pressing the ON/OFF button will turn the light or fan (controlled load) ON and OFF. Unlike a standard switch, 

the CS-50 automatically turns OFF the controlled load after the coverage area has been vacant for a period of time known as the Time 

Delay. If motion is detected within 30 seconds after it automatically turns OFF, the CS-50 automatically turns the load back ON.

Indicator Light

The Status LED located on the ON/OFF button blinks upon initial detection.  It will blink again when it detects a change of infrared 

energy in the space. The LED can be disabled. See 

Status LED

.

INITIAL POWER UP DELAY

There is an initial warm-up and calibration period the first time power is applied to the unit after a power failure lasting more than 5 

minutes, and after the load is replaced.

COVERAGE AREA 

The CS-50 has a maximum coverage range of 180 degrees and a coverage area of 600 square 

feet (56 square meters). The sensor must have a clear and unobstructed view of the coverage 

area. Objects blocking the sensor’s lens may prevent detection thereby causing the light to turn off 

even though someone is in the area.

NOTE: Windows, glass doors, and other transparent barriers will obstruct the sensor’s 

view and prevent detection.

Fig 1: Sensor Coverage Area

P

P

Summary of Contents for Wattstopper CS-50













Reviews: