5
Reset to Factory Default
Press
and
hold
the Up or Down button for
5 seconds
. The green LED will flash 3 times to indicate the reset is complete. Return the DIP
Switches 6–9 to the OFF state. This resets the sensor and disables light level control (the brightest ambient light will not hold the light
OFF
).
DIP SWITCH SETTINGS
=ON =OFF
1
Auto - On
Manual - On
Mode
9
1 2 3 4 5 6 7 8
Time
Delay
Mode
ON
Additional
Features
Trigger
Test/3 min
15 minutes
30 minutes
5 minutes
2 3
Time Delay
Exit Programming Mode
Audio Alert
Walk-Thru
Visual Alert
6 7
Additional Features
8 9
PIR Sensitivity
High Trim
Low Trim
Ramp Up Time
Fade Down Time
Light Level Adjust
Power Loss Mode
Presentation Mode
Service Mode
Preset On Level
Non-Dim Mode
Green LED # of Blinks
1=OFF
, 2=ON
1=ON
, 2=OFF
1=OFF
, 2=ON
1=100%
, 2=50%
1=1
, 2=2.5, 3=5, 4=10s
1=2.5
, 2=5, 3=15, 4=30s
1=Last Non-Zero Value
,
2=50%, 3=75%, 4=100%
1=10V
, 2=Manual Adjustment
1=0V
, 2=Manual Adjustment
1=Disable
, 2=Enable,
3=Smart Light Level
Reset To Default
1=Keep Last State
,
2=Default On, 3=Default Off
1=OFF
, 2=ON
1=ON
, 2=OFF
Press and Hold UP or
DOWN for 5 seconds
1=OFF
, 2=ON
Default Values Shown in
Bold
4 5
Trigger
Mode
Initial
Occupancy
Maintain Occupancy
Re-trigger
Option C
Both
Both
Both
Standard
Either
Either
Option A
Either Either
PIR
Both
Option B
PIR
PIR
PIR
TROUBLESHOOTING
Lights do not turn ON with motion (LED does flash)
1. Press and and hold the
UP
button to make sure that the correct lights come
ON
. If the lights do
NOT
turn
ON
, check wire
connections, especially the Load connection. If the lights turn
ON
, verify that the correct
On Mode
is selected with DIP switch 1.
2. Check to see if light level control is enabled: cover the sensor lens with your hand. If the lights come
ON
, adjust the light level setting.
3. If lights still do not turn
ON
, call 800.879.8585 for technical support.
Lights do not turn ON with motion (LED does not flash)
1. Press and holde the
UP
button to make sure that the correct lights come
ON
. If the lights turn
ON
, verify that Sensitivity is on High.
2. Check the wire connections, in particular, the Line connection. Verify that connections are tightly secured.
3. If lights still do not turn
ON
, call 800.879.8585 for technical support.
Lights do not turn OFF
1. There can be up to a 30 minute time delay after the last motion is detected. To verify proper operation, set switches 2 and 3 to
OFF
to start Test Mode. Move out of view of the sensor. The lights should turn
OFF
in approximately 10 seconds.
2. Verify that the sensor is mounted at least six feet (2 meters) away from any heating/ventilating/air conditioning device that may
cause false detection. Verify that there is no significant heat source (e.g., high wattage light bulb) mounted near the sensor.
3. If the lights still do not turn
OFF
, call 800.879.8585 for technical support.
Sensing motion outside desired areas
1. Mask the PIR sensor’s lens to eliminate unwanted coverage area.
2. Select PIR Sensitivity. See
PIR Sensitivity Adjustment
and
DIP Switch Settings
.
Red LED is OFF all the time and the sensor features don’t work.
1. Double check the setting for Service Mode to see if it is turned
ON
. If so, turn it
OFF
. Also check the setting of the Time Delay
function. See the section on
DIP Switch Settings
.
2. If the problem still exists, call technical support.
COVER PLATES
WattStopper DW series wall switches fit behind industry standard decorator-style switch cover plates. Cover plates are not included.
Units come in the following colors, which are indicated by the final suffix of the catalog number (shown here in parentheses):
• White (–W)
• Gray (–G)
• Ivory (–I)
• Light Almond (–LA)
• Black (–B)
• Red (–R)