background image

Installation Instructions

 LFE1U

9

9.

Remove back cover to expose control box. (See Figure 6)

10. Route control pad cable (D)  behind bottom back cover (A1) 

and into port A1 on control box. 

(See Figure 6) and (See 

Figure 7)

11. Route motor cable (E) behind bottom back cover (A1) and 

into port 1 on control box. 

(See Figure 6) and (See 

Figure 7)

NOTE:  

Bottom back cover (A1) may need to be pulled back or 
loosened in order to fit cables behind it.

NOTE:  

Use cable ties (K) and pre-installed cable clips to 

provide tension relief.

NOTE:  

Knockout holes can be created on A1 bracket for 

another cable routing option. (See Figure 7) 

Figure 6

IMPORTANT ! : 

Lower cover (A2) should only be 

installed after all cables have been routed with no load.

12. Slide lower cover (A2) onto column assembly (P) and use 

two 8-32 x 3/8" Phillips pan machine screws (F) to secure 

bottom back cover (A1) to lower cover (A2). (See Figure 7)

Figure 7

13. Plug in power cable (V) to control box and route along side 

of control box. Provide strain relief using the cable ties (K) 

and cable clips. All three cable clips MUST be used to 

prevent cable from rubbing against lower edge of cover! 

(See Figure 8)

Figure 8

14. Plug in power cable (V) to outlet.

15. Press and hold "DOWN" button for three seconds to 

initialize lift mechanism. (See Figure 9)

16. Press and hold "UP" button until mount reaches it’s 

maximum height. (See Figure 9)

NOTE:  

If lifting mechanism does not function properly refer to 

"Troubleshooting" Section.

Figure 9

(D)

10

9

(C)

(E)

into port "A1"

into port "1"

11

(K) x 4 for tension relief 

(as needed)

(A2)

12

12

(A1)

(F) x 2

12

knockout
holes

control box

13

required clip

locations

"UP"

"DOWN"

"PRESETS" "SAVE"

Summary of Contents for Chief LFE1U





















Reviews: