background image

 LFE1U

Installation Instructions

18

Tilt Adjustment

IMPORTANT ! : 

Remove display from mount prior to 

adjusting tilt!

5.

Use 3/16" hex key (H) to remove tilt adjustment screws on 

both sides. (See Figure 33)

6.

Adjust faceplate tilt and re-install removed screw in either 

the middle hole for 2° tilt or the lowest hole for 4° tilt. (See 

Figure 33)

Figure 33

Roll Adjustment

7.

Loosen nuts on back of faceplate. (See Figure 34)

8.

Adjust roll as desired. (See Figure 34)

9.

Tighten nuts on back of faceplate. (See Figure 34)

Figure 34

Troubleshooting

If lifting function does not work properly, try to following 
troubleshooting steps. If none of these work, contact customer 
service.

1.

If there is uneven movement, initialize the control box 

(reset)

Hold "Down" button until lift has reached it’s lower 

limit.

Briefly release "Down" button

Press and hold "Down" for five seconds, wait until 

all movement has stopped, then release

2.

If there is no movement, check the following

Check all cable connectors between controllers 

and actuators.

Check power cable connection to control box.

3.

If there is slight movement and then reverse travel, check 

for any obstructions that may be interfering such as cables 

or peripheral devices.

4.

Contact customer service if none of the above steps fix the 

problem.

5

6

6

remove

re-install

(rear view)

8

7

9

Summary of Contents for Chief LFE1U





















Reviews: